SEWTECHSupport Center 简体中文

Thread the ST-1201 and SC-1501

Applies to ST-1201 / SC-1501 Demonstrated on ST-1201

Watch on YouTube ↗

Overview

Use this guide to thread the upper thread with the machine stationary. Have your spools, the long hooked wire threader from the toolbox and small scissors ready. The ST-1201 demonstration follows two of its 12 positions, from the spool rack to the needle and the tail holder. Use the position numbers on your machine to keep each thread on its own route.

Step-by-step guide

1. Match the spool to its needle number

Watch at 00:13

The ST-1201 in the video has 12 spool positions. Start with the number of the needle you want to thread. On the rack, use the guide hole directly above that spool. The video uses yellow for No. 1 and green for No. 2 so you can follow the two routes.

The numbers over the spools show their order on the ST-1201 rack.
The numbers over the spools show their order on the ST-1201 rack.
The finger points to the guide plate above the corresponding spools.
The finger points to the guide plate above the corresponding spools.

2. Find the matching slot on the guide plate

Watch at 01:20

Look down at the guide plate above the spools. The plate has a separate slotted path for each position. Match the spool, guide plate path and needle by number. In the following close-ups, No. 1 is the far-right path when you face the front of the machine.

The overhead view maps the 12 slots to the spool and needle numbers.
The overhead view maps the 12 slots to the spool and needle numbers.
The yellow and green spools are the two examples used in the lesson.
The yellow and green spools are the two examples used in the lesson.

3. Bring the thread up and back down through the plate

Watch at 01:52

Pull the end from spool No. 1. Feed it up from underneath through the first No. 1 hole above the spool. Lay the thread in the connecting slot on top and pass it down through the second hole at the other end of that same slot. Reach underneath and pull the end down.

Lift the thread from the yellow spool into the guide hole above it.
Lift the thread from the yellow spool into the guide hole above it.
Feed the thread down through the second hole of the same slot.
Feed the thread down through the second hole of the same slot.
The inset shows the thread coming out underneath the plate.
The inset shows the thread coming out underneath the plate.

4. Free the tube and feed the thread through the inlet

Watch at 02:25

Take the matching flexible tube out of its mounts so you can hold it in your hands. With the upper tube end out of the guide-plate mount, lead the loose end through the exposed opening at that position. The underside close-up shows the line coming out of the second hole and turning toward the tube mount.

Lift the upper fitting out of its slot before releasing the lower end.
Lift the upper fitting out of its slot before releasing the lower end.
The flexible tube is out of its mounts. Its white ends identify where it seats.
The flexible tube is out of its mounts. Its white ends identify where it seats.
The inset shows the underside route into the exposed tube-mount opening.
The inset shows the underside route into the exposed tube-mount opening.

5. Pull the thread through with the wire threader

Watch at 02:44

Take the long wire threader with a hook from the toolbox. Feed it into the loose tube until its hook comes out of the other end. Catch the yellow thread on the exposed hook, then draw the wire back through the tube slowly. Check that the yellow thread has come out of the opposite white fitting before unhooking it.

Use the long wire threader from the toolbox.
Use the long wire threader from the toolbox.
The wire extends beyond the white tube fitting.
The wire extends beyond the white tube fitting.
Catch the yellow thread on the small hook before pulling the wire back.
Catch the yellow thread on the small hook before pulling the wire back.
The yellow thread is now visible outside the tube fitting.
The yellow thread is now visible outside the tube fitting.

6. Refit the tube to the same position

Watch at 03:18

Put the upper fitting back into its slot at the guide plate and return the lower fitting to the same position above the pre-tension discs. Keep hold of the free end. Check that the tube is seated at both ends and that the thread still extends from the lower fitting.

The inset shows the upper white fitting going back into the guide-plate slot.
The inset shows the upper white fitting going back into the guide-plate slot.
The inset shows the lower fitting returning to its mount above the tension discs.
The inset shows the lower fitting returning to its mount above the tension discs.

7. Seat the thread between the pre-tension discs

Watch at 03:25

Directly below the tube outlet, bring the thread behind the small black knob in the top row. Hold the two sides of the thread and draw it into the gap between the shiny discs. Check from the side that the thread sits in the gap before leading it to the small wheel below.

The top-row knob is directly below the tube outlet.
The top-row knob is directly below the tube outlet.
The side view shows the yellow thread between the metal discs.
The side view shows the yellow thread between the metal discs.

8. Wrap the small wheel once clockwise

Watch at 03:33

Facing the front of the machine, take the thread around the small dotted wheel directly below the pre-tension discs, one full turn clockwise. Keep it seated in the rim and bring it down to the small guide hook above the main tension wheel.

The original on-screen tip calls for one clockwise turn on the small wheel.
The original on-screen tip calls for one clockwise turn on the small wheel.
After the wrap, the yellow thread exits on the right in the No. 1 close-up.
After the wrap, the yellow thread exits on the right in the No. 1 close-up.

9. Wrap the main tension wheel one and a half turns

Watch at 03:39

After passing through the guide above the larger wheel, wrap around the rim behind the large black tension knob. Looking from the front, make one full clockwise turn and then another half turn. Bring the thread into the wire hook at the left of the No. 1 wheel as shown.

Before wrapping the larger wheel, pass through the black hook directly above it.
Before wrapping the larger wheel, pass through the black hook directly above it.
The inset shows the thread around the large wheel. This wheel takes one and a half clockwise turns.
The inset shows the thread around the large wheel. This wheel takes one and a half clockwise turns.
The thread has moved from the wheel into the wire hook beside it.
The thread has moved from the wheel into the wire hook beside it.

10. Follow the two lower guide hooks

Watch at 03:55

From the wire hook beside the main wheel, lead the thread through the black guide immediately beneath the knob. Continue down through the matching black guide on the row just above the slotted black cover. Follow the same needle position all the way down.

The yellow thread is seated in the guide directly below the No. 1 tension knob.
The yellow thread is seated in the guide directly below the No. 1 tension knob.
The presenter seats the thread in the last black guide above the slotted cover.
The presenter seats the thread in the last black guide above the slotted cover.

11. Go down one hole, around the steel bar and up the next

Watch at 04:02

At the ledge below the take-up levers, feed the thread down through the first hole for your position. Reach under the ledge and take the thread around the steel bar. Bring it back up through the next hole for that position. In the No. 1 close-up, you can see the thread entering one hole at the right end and the free end reappearing beside it.

Start by pushing the end down through the first hole on the black ledge.
Start by pushing the end down through the first hole on the black ledge.
The inset shows the bar underneath, and the main view shows the end coming up through the next hole.
The inset shows the bar underneath, and the main view shows the end coming up through the next hole.

12. Thread the take-up lever and return to the lower hole

Watch at 04:12

Lift the emerging end to the eye in the silver take-up lever for the same needle position. Pass the end through the eye, then bring it down through the return hole on the ledge below. Verify that the thread runs up to the lever and back down through the guide toward the needle.

The yellow thread passes through the silver take-up lever eye.
The yellow thread passes through the silver take-up lever eye.
Bring the free end down into the return hole below the lever.
Bring the free end down into the return hole below the lever.
The path goes up to the lever and back down toward the needles.
The path goes up to the lever and back down toward the needles.

13. Guide the thread under the bar and through the needle

Watch at 04:23

At the corresponding needle, slip the thread under the small presser bar shown in the close-up. Lift the bar slightly with a finger to make room, then draw the thread toward the needle. Insert the end into the needle eye from front to back and pull it through.

A finger lifts the small bar above the needles so the thread can pass underneath.
A finger lifts the small bar above the needles so the thread can pass underneath.
The yellow thread exits from under the bar and is held near the needle.
The yellow thread exits from under the bar and is held near the needle.
The close-up shows the yellow thread through the needle eye.
The close-up shows the yellow thread through the needle eye.

14. Tuck the tail under the bar and trim the excess

Watch at 04:38

After the needle is threaded, bring the tail back up to the same bar. Lift it slightly, slide the tail underneath and pull it through. Use the small scissors to trim the excess beyond the bar. Check that the remaining tail is held and that the thread is still through the needle.

The presenter lifts the bar to tuck the tail back underneath.
The presenter lifts the bar to tuck the tail back underneath.
The scissors trim the excess after the tail is held under the bar.
The scissors trim the excess after the tail is held under the bar.

15. Repeat on No. 2 and check each completed path

Watch at 04:50

Repeat with the green spool using the No. 2 guide hole above it and the matching tube, discs, wheels, hooks, lever and needle. The video gives a faster second demonstration on No. 2. Before stitching, trace each color from its spool to its own needle. Check that both ends of the tube are seated, wraps are in the wheel grooves, the guides hold the thread and the thread passes through the needle eye.

The green thread goes through its own guide-plate slot.
The green thread goes through its own guide-plate slot.
The green thread uses the neighbouring tension path for No. 2.
The green thread uses the neighbouring tension path for No. 2.
Yellow and green reach separate needle positions. Trace each color to its own needle.
Yellow and green reach separate needle positions. Trace each color to its own needle.