SEWTECHSupport Center 简体中文

Combine Two Embroidery Designs on the ST-1501

Applies to ST-1501

Watch on YouTube ↗

Overview

Combine two designs already saved on the ST-1501 controller. Choose the first design as the reference, position the second with the X and Y offsets, then save the combination and verify it in the design list. The video demonstrates the touchscreen workflow through the saved preview.

Step-by-step guide

1. Select the first design and note the second number

Watch at 00:23

Open the design list on the ST-1501 and locate both saved designs. Tap the thumbnail you want to use first. In the video it is 526, the wing design. Note the number of the second design, 528, the Butterfly lettering, and keep the first design selected.

The first thumbnail is design 526, shown with the wing outline.
The first thumbnail is design 526, shown with the wing outline.
The adjacent Butterfly lettering is design 528. Use its number on the second settings screen.
The adjacent Butterfly lettering is design 528. Use its number on the second settings screen.

2. Open Create Combine Pattern

Watch at 00:30

While the first design is selected, tap the four-color square icon on the right side of the lower panel, below the blue rectangular icon. In the menu, tap Create Combine Pattern. The controller opens the settings for the first design.

Tap the four-color square in the right-hand column of the design screen.
Tap the four-color square in the right-hand column of the design screen.
Choose Create Combine Pattern from the menu. The video enlarges the selected row.
Choose Create Combine Pattern from the menu. The video enlarges the selected row.

3. Check the first design number

Watch at 00:39

Check the Design No field in the top row of the first settings screen. The controller brings in the design already selected in the list, so keep that number if it matches your first design. The demo shows 526.

The highlighted top field already contains 526 from the design list.
The highlighted top field already contains 526 from the design list.

4. Set the first design’s scale and orientation

Watch at 00:51

Use X Zoom Scale and Y Zoom Scale for horizontal and vertical scaling, Rotate Angle for rotation, and Direction for the flip orientation. The demo leaves both scales at 100 and the rotation at 0. When the first design is set, tap the right arrow beside the page counter at the lower left to open the second settings screen.

X Zoom Scale and Y Zoom Scale are the two rows directly below Design No.
X Zoom Scale and Y Zoom Scale are the two rows directly below Design No.
Rotate Angle is set to 0 in the demo.
Rotate Angle is set to 0 in the demo.
The Direction row uses a P-shaped symbol to show orientation.
The Direction row uses a P-shaped symbol to show orientation.
Tap the right arrow beside the page counter to continue.
Tap the right arrow beside the page counter to continue.

5. Enter the second design number

Watch at 01:02

On the second settings screen, tap the top Design No field and enter the number you noted earlier. Tap the blue check mark on the numeric keypad, then verify that the top row shows the second design number. The demo changes this field from 526 to 528.

Tap the Design No value at the top of the second settings screen.
Tap the Design No value at the top of the second settings screen.
The keypad shows 528. Tap its check mark to confirm the second design.
The keypad shows 528. Tap its check mark to confirm the second design.
After confirming the keypad, the top row shows 528.
After confirming the keypad, the top row shows 528.

6. Review the second design’s layout and spacing fields

Watch at 01:12

Review the second design’s scale, rotation and direction as you did for the first. At the bottom, use X space to the first design for the horizontal offset and Y space to the first design for the vertical offset. Both offsets are relative to the first design.

The upper spacing row is the X offset from the first design.
The upper spacing row is the X offset from the first design.
The lower spacing row is the Y offset from the first design.
The lower spacing row is the Y offset from the first design.

7. Enter the spacing for your layout

Watch at 01:26

Tap the value box for the axis you want to change. In the demo, the operator opens Y Interval, enters 50 and taps the keypad check mark. Check the values after the keypad closes. The example shows X = 0 and Y = 50. Choose values that suit your own two designs.

Tap the bottom value box to edit the Y offset.
Tap the bottom value box to edit the Y offset.
The Y Interval keypad shows 50. Tap its check mark to accept the entry.
The Y Interval keypad shows 50. Tap its check mark to accept the entry.
Back on the settings page, X is still 0 and Y now reads 50.
Back on the settings page, X is still 0 and Y now reads 50.

8. Confirm the two designs’ settings

Watch at 01:32

Once the second design and spacing are correct, tap the check mark at the lower right of the settings page, beside the exit icon. The next screen shows New Pattern Num and New Pattern Name for the combined design.

The settings-page check mark opens the screen for the new design.
The settings-page check mark opens the screen for the new design.
The next screen shows separate fields for the new number and name.
The next screen shows separate fields for the new number and name.

9. Set the combined design’s number

Watch at 01:36

Tap New Pattern Num, enter the number you want to give the combined design, and tap the numeric keypad check mark. The video changes the suggested number from 527 to 529.

The top field is New Pattern Num. Tap its value to open the number keypad.
The top field is New Pattern Num. Tap its value to open the number keypad.
The keypad shows 529. Tap the blue check mark to use that number.
The keypad shows 529. Tap the blue check mark to use that number.

10. Name the combined design

Watch at 01:41

Tap New Pattern Name to open the name keypad. Enter the name you want to see in the design list, then tap the check mark inside the keypad. The demo uses Combine.

Tap New Pattern Name below the number to open the name keypad.
Tap New Pattern Name below the number to open the name keypad.
Combine is visible in the name field before the keypad is closed.
Combine is visible in the name field before the keypad is closed.

11. Save and wait for the completion message

Watch at 01:45

Verify the number and name on the save screen, then tap the lower-right check mark on that screen. The controller briefly processes the design. Wait for the message “Create Combine Pattern finished!” before leaving.

This check mark on the save screen starts creating the combined design.
This check mark on the save screen starts creating the combined design.
The progress indicator appears with 529 and Combine still visible above it.
The progress indicator appears with 529 and Combine still visible above it.
The completion message confirms the controller has created the combined design.
The completion message confirms the controller has created the combined design.

12. Find the new thumbnail in the design list

Watch at 01:55

Dismiss the completion message with the icon at the lower right of the popup. Return to the main design list and look for your new number and name. In the demo, 529_Combine.DST appears alongside 526 and 528, with both the wings and the Butterfly lettering in one thumbnail. Use this preview to verify the saved combination and its placement.

The lower-right popup button closes the completion message.
The lower-right popup button closes the completion message.
The lower-right thumbnail is 529_Combine.DST and shows the two designs together.
The lower-right thumbnail is 529_Combine.DST and shows the two designs together.