SEWTECHSupport Center 简体中文

Fix Error 9 at the Start of an Embroidery Design

Applies to ST-1501 / SC-1501 Demonstrated on ST-1501

Watch on YouTube ↗

Overview

This guide covers Error 9 when the controller is asked to back up before the first stitch. On the ST-1501 shown, clear the message, exit stitch controls and leave the design at stitch 0 until you are ready to start.

Step-by-step guide

1. Enter embroidery mode

Watch at 00:12

With the design selected and the machine idle, tap the red embroidery-mode button at the far right of the strip below the design area. In the “Confirm EMB?” dialog, tap the check mark. Wait for loading to finish. On this controller the button turns blue and the design preview appears. Proceed to the stitch count with the machine still idle.

The red box marks the embroidery-mode button at the far right of the strip.
The red box marks the embroidery-mode button at the far right of the strip.
Tap the check mark indicated by the arrow in “Confirm EMB?”.
Tap the check mark indicated by the arrow in “Confirm EMB?”.
Wait while the controller loads the selected design.
Wait while the controller loads the selected design.
The F preview appears and the mode button turns blue after loading.
The F preview appears and the mode button turns blue after loading.

2. Read the stitch counter below the preview

Watch at 00:19

Check the current/total stitch count in the status fields directly below the preview. The display reads 0/5243 for the example design. The first number is the current position. If it is 0, the design is already at its starting point.

In the highlighted 0/5243 field, 0 is the current stitch and 5243 is this design’s total.
In the highlighted 0/5243 field, 0 is the current stitch and 5243 is this design’s total.

3. Locate the stitch controls

Watch at 00:27

For reference, the video opens stitch controls with the needle icon flanked by left and right arrows. It is the upper-right button in the six-button cluster to the left of the directional pad. The lower part of the display changes to the stitch controls and the design preview stays above it. If the Error 9 dialog is already open, go to the dismissal step.

The arrow points to the stitch-controls icon at the upper right of the six-button cluster.
The arrow points to the stitch-controls icon at the upper right of the six-button cluster.
The stitch controls replace the directional pad in the lower screen area.
The stitch controls replace the directional pad in the lower screen area.

4. Match the Error 9 message

Watch at 00:29

The video reproduces the fault by tapping −1 (the left button in the second row of stitch controls) at stitch 0. The dialog reads “Err No = 9:Back end and pull back bar”. The controller has no earlier stitch to move to. If this matches your screen, clear the dialog and continue from the current position.

The −1 button in the second row is the one-stitch-back command shown in the video.
The −1 button in the second row is the one-stitch-back command shown in the video.
The dialog identifies Error 9 after the attempt to back up from stitch 0.
The dialog identifies Error 9 after the attempt to back up from stitch 0.

5. Dismiss the error dialog

Watch at 00:35

Tap the return icon at the bottom right inside the Error 9 dialog. Check that the pop-up disappears. The stitch controls below the design are still open, so use their own Exit button in the next step.

Use the return icon inside the error pop-up.
Use the return icon inside the error pop-up.
The pop-up is gone and the stitch controls remain below the design preview.
The pop-up is gone and the stitch controls remain below the design preview.

6. Exit the stitch controls

Watch at 00:42

Tap the exit icon in the lower-right corner of the pale stitch-control panel, directly above the blue gear button. The main embroidery screen returns with the directional pad and six-button cluster. The blue embroidery-mode button stays visible.

The exit icon is on the pale panel directly above the blue gear button.
The exit icon is on the pale panel directly above the blue gear button.
The directional pad and six-button cluster show that the main screen is back.
The directional pad and six-button cluster show that the main screen is back.

7. Check the setup before starting

Watch at 00:48

On the main screen, check that the intended design is displayed, the controller is in embroidery mode and the current stitch is still 0. Before pressing Start, make sure the hoop is secure, the fabric and stabilizer are seated, the machine is threaded and the hoop path is clear. The video calls for a setup check and keeps the camera on the controller.

The red box marks the blue embroidery-mode indicator on the main screen.
The red box marks the blue embroidery-mode indicator on the main screen.

8. Leave the design at stitch 0

Watch at 00:55

The video reopens the stitch controls to show what to avoid. When the first number in the current/total counter is 0, leave the position there and use the panel’s Exit icon if it is open.

The red box shows the stitch-movement keys in the repeat demonstration.
The red box shows the stitch-movement keys in the repeat demonstration.
The counter still reads 0/5243 in the repeat demonstration.
The counter still reads 0/5243 in the repeat demonstration.

9. Press Start and check the first stitches

Watch at 01:07

Once the main screen is back and the setup is ready, press the physical Start button with the blue ring below the left side of the touchscreen. On your machine, verify that stitching starts, the stitch count advances from 0 and the Error 9 prompt stays closed. The clip shows the button press and then cuts to the presenter.

The presenter exits stitch controls again to return to the main screen.
The presenter exits stitch controls again to return to the main screen.
Start is the physical button with the blue ring below the left side of the touchscreen.
Start is the physical button with the blue ring below the left side of the touchscreen.