SEWTECHSupport Center 简体中文

Embroider a T-shirt on the ST-1201 and SC-1501

Applies to ST-1201 / SC-1501 Demonstrated on ST-1201

Watch on YouTube ↗

Overview

Follow the left-chest logo project demonstrated on the ST-1201, from marking and hooping the shirt through USB import, arm setup, a laser trace and a finished stitch-out. The 100 × 100 mm hoop, the right-arm hole and the needle numbers are the setup used in this demonstration.

Step-by-step guide

1. Gather the materials and choose a hoop

Watch at 00:22

Set out the shirt, the hoop and its two mounting arms, a full bobbin, a washable fabric pen, a wrench set and stabilizer. Have scissors, tape, a placement template and a USB drive with the design ready for the later steps. Compare the design with the hoop opening and choose a hoop that is larger than the design.

The support arms and hoop are on the left of the worktable, with the garment and small tools laid out beside them.
The support arms and hoop are on the left of the worktable, with the garment and small tools laid out beside them.
The yellow placement template sits inside the hoop opening to illustrate the size check.
The yellow placement template sits inside the hoop opening to illustrate the size check.

2. Mark and tape the left-chest placement

Watch at 00:58

Lay the shirt front up. Mark the desired logo center on the wearer’s left chest with the washable pen. The presenter starts with the center already marked. Match the center hole in the yellow template to that mark, then tape the template to the shirt so it stays in place while hooping.

The small cross on the shirt marks the logo center.
The small cross on the shirt marks the logo center.
The template center sits over the cross while tape secures the template edge.
The template center sits over the cross while tape secures the template edge.

3. Cut the stabilizer larger than the hoop

Watch at 02:10

The video uses cut-away stabilizer for this shirt. Lay the lower hoop ring on the sheet as a size guide. Cut with scissors, leaving stabilizer beyond the hoop on every side so it can be caught between the rings.

The lower ring is used to check how much stabilizer to unroll.
The lower ring is used to check how much stabilizer to unroll.
The cut line leaves stabilizer extending past the hoop edge.
The cut line leaves stabilizer extending past the hoop edge.

4. Hoop the shirt front and hand-tighten

Watch at 02:48

Loosen the adjusting screw on the lower ring slightly. Lay the cut-away over the ring and slide both up inside the shirt, directly behind the marked front panel. Center the template in the ring and smooth the knit without stretching it. Press the upper ring down evenly. Lift the loose garment edge to reach the adjustment screw and tighten it by hand. Check that the template is centered and the fabric inside the hoop is flat.

The screw on the lower ring is loosened before the layers go in.
The screw on the lower ring is loosened before the layers go in.
The lower ring and stabilizer go up through the hem, between the front and back layers.
The lower ring and stabilizer go up through the hem, between the front and back layers.
The upper ring is pressed down with the template centered in the opening.
The upper ring is pressed down with the template centered in the opening.
The presenter lifts the loose fabric to reach and tighten the adjusting screw.
The presenter lifts the loose fabric to reach and tighten the adjusting screw.

5. Import the design from USB

Watch at 04:05

Turn on the machine and insert the USB drive into the right edge of the touchscreen. Tap the USB icon on the right side of the design list and wait for the drive thumbnails. Tap the intended design, tap the orange import icon on the right, then tap the check mark in the dialog. Use the lower-right return button and check that the new thumbnail is in the machine’s design list.

The USB drive is inserted on the right edge and the finger points to the USB command on the screen.
The USB drive is inserted on the right edge and the finger points to the USB command on the screen.
The upper thumbnails show the drive contents. The S-and-clover design is the selected example.
The upper thumbnails show the drive contents. The S-and-clover design is the selected example.
The orange icon on the right imports the selected design.
The orange icon on the right imports the selected design.
Use the check mark in the import dialog to confirm.
Use the check mark in the import dialog to confirm.
The S-and-clover thumbnail appears in the machine’s own list after returning.
The S-and-clover thumbnail appears in the machine’s own list after returning.

6. Assign the thread colors in stitch order

Watch at 05:14

Open the thread-color tab in the middle row of the screen. Follow the digitizer’s color chart and choose the needle carrying the required thread for each color stop. The demo uses brown on needle 11 first and green on needle 8 second. Check both rows and the brown-and-green preview on your screen. Use your own threaded needle positions for other designs or setups.

The finger points to the color tab just below the design information.
The finger points to the color tab just below the design information.
The printed color chart lists the stitch colors in order.
The printed color chart lists the stitch colors in order.
The brown section is assigned to needle 11 on the color grid.
The brown section is assigned to needle 11 on the color grid.
The green section is assigned to needle 8 on the same color grid.
The green section is assigned to needle 8 on the same color grid.
The sequence and preview now show brown first and green second.
The sequence and preview now show brown first and green second.

7. Select the actual hoop on the controller

Watch at 06:14

Open the positioning tab just to the right of the color tab. Tap the hoop selector in the left control group. Choose the physical hoop you are using. The video selects 100 × 100 mm, the top-middle tile. Tap the lower check mark, read the frame-motion prompt and tap its check mark with the area clear. The preview returns with the new green hoop boundary around the design.

The hoop selector is in the left control group of the positioning screen.
The hoop selector is in the left control group of the positioning screen.
The top-middle tile is the 100 × 100 mm hoop used in the video.
The top-middle tile is the 100 × 100 mm hoop used in the video.
Read the movement prompt and use its check mark when the frame area is clear.
Read the movement prompt and use its check mark when the frame area is clear.
The square green boundary is visible after the profile is applied.
The square green boundary is visible after the profile is applied.

8. Prepare the hoop-arm mounting screws

Watch at 06:56

With the machine stopped, get the left and right hoop arms. Use the wrench to loosen the screws on the arm mounting plates. Once loose, remove them by hand and keep them for refitting.

The wrench loosens the screws on the hoop-arm mounting plates.
The wrench loosens the screws on the hoop-arm mounting plates.
The mounting plates are shown with the screws removed.
The mounting plates are shown with the screws removed.

9. Fasten the right arm at the demonstrated hole

Watch at 07:24

Face the machine and position the right arm against the right carriage rail. In this setup the indicated mounting hole lines up with machine hole No. 3. Start both screws by hand, then use the wrench to tighten both. The No. 3 position is the example for this hoop and setup.

The presenter points out the reference hole on the right carriage rail.
The presenter points out the reference hole on the right carriage rail.
Both screws have been started in the right arm’s mounting plate.
Both screws have been started in the right arm’s mounting plate.
Tighten the pair of screws with the wrench.
Tighten the pair of screws with the wrench.

10. Set the left-arm width with an empty hoop

Watch at 08:21

The left carriage side has a slot. Fit an empty hoop of the same size and slide the left arm until the hoop sits straight and centered between the two arms. Hold the left arm still, start its two screws and tighten them with the wrench. Check both sides and gently check for wobble. Remove the empty hoop before loading the shirt.

The left carriage rail has a slot for sliding the arm.
The left carriage rail has a slot for sliding the arm.
The empty hoop sets the distance between the arms.
The empty hoop sets the distance between the arms.
Hold the arm at the fitted position and tighten its two screws.
Hold the arm at the fitted position and tighten its two screws.
The empty hoop sits straight and centered on both arms.
The empty hoop sits straight and centered on both arms.

11. Check the bobbin before loading the shirt

Watch at 09:43

Open the bobbin cover under the needle area and pull out the bobbin case. Check how much thread remains. If it is nearly empty, replace the bobbin with a full one as shown. Refit the bobbin case and close the cover before the shirt goes onto the machine.

The cover opens below the needle head to expose the bobbin case.
The cover opens below the needle head to expose the bobbin case.
Check the thread remaining in the removed bobbin.
Check the thread remaining in the removed bobbin.
The presenter fits a full bobbin into the case.
The presenter fits a full bobbin into the case.
After refitting the case, close the cover before mounting the hoop.
After refitting the case, close the cover before mounting the hoop.

12. Slide the shirt hoop into both arms

Watch at 10:29

Guide the shirt around the bobbin area so the hooped front is over the needle plate and the loose back and hem hang clear. Feed both metal hoop tabs into the arms, slide them inward, lift the bracket slightly as shown and press the hoop in until it clicks. Check that both sides are fully seated. The yellow placement template is already gone in this shot. Use the washable mark for alignment and remove the paper and tape before stitching.

The shirt hangs around the free arm while the two hoop tabs enter their supports.
The shirt hangs around the free arm while the two hoop tabs enter their supports.
This close-up shows the bracket lifted slightly as the hoop is seated.
This close-up shows the bracket lifted slightly as the hoop is seated.
With both sides seated, the shirt hangs below the frame and clear of the stitch area.
With both sides seated, the shirt hangs below the frame and clear of the stitch area.

13. Move the design to the placement mark

Watch at 10:55

On the positioning screen, use the directional pad to move the frame and align the design center with the mark on the shirt. Tap the animal icon in the middle of the arrows to switch movement speed. The turtle makes smaller, slower moves and the rabbit moves faster. Check that the design still lies entirely inside the green hoop outline.

The arrow pad on the right moves the hoop for alignment.
The arrow pad on the right moves the hoop for alignment.
The middle button switches between the turtle and rabbit movement speeds.
The middle button switches between the turtle and rabbit movement speeds.
The entire design outline should fit inside the green hoop boundary.
The entire design outline should fit inside the green hoop boundary.

14. Trace the design and verify clearance

Watch at 11:44

Tap the trace icon in the left control group and confirm the movement prompt with its check mark. Watch the red laser point as the hoop moves along the design outline. Check the full path against the actual hoop edge. If the path approaches the frame or runs outside it, reposition the design and run the trace again before starting.

The finger indicates the trace icon on the positioning screen.
The finger indicates the trace icon on the positioning screen.
The trace prompt appears before the carriage moves.
The trace prompt appears before the carriage moves.
Watch the red laser point on the shirt as the frame moves. Its path needs to stay inside the hoop.
Watch the red laser point on the shirt as the frame moves. Its path needs to stay inside the hoop.

15. Confirm embroidery and press Start

Watch at 12:07

After the trace clears the frame, tap the red embroidery control on the right of the middle bar. Tap the same area again as shown to bring up the confirmation, then confirm on screen. When the design reappears with the color sequence on the right, press the blue-ring physical Start button below the screen. Observe the first stitches and keep the loose garment clear as the hoop moves.

The red control at the right end of the bar switches into embroidery mode.
The red control at the right end of the bar switches into embroidery mode.
The on-screen prompt must be confirmed before starting.
The on-screen prompt must be confirmed before starting.
Press the physical blue-ring Start button below the touchscreen.
Press the physical blue-ring Start button below the touchscreen.
The needle begins stitching inside the hoop on the shirt front.
The needle begins stitching inside the hoop on the shirt front.

16. Wait for completion, then remove the hoop

Watch at 12:46

Wait for the machine to stop and the “Embroidery completed!” message to appear. Support both sides of the hoop, lift to release it and draw it out as shown. Check the finished logo against the left-chest placement and the planned brown and green sequence. The video shows the shirt out of the hoop at the end and skips the backing cleanup.

The controller displays “Embroidery completed!” above the controls.
The controller displays “Embroidery completed!” above the controls.
The presenter lifts the frame at the arms to release it.
The presenter lifts the frame at the arms to release it.
The brown S and green clovers are complete on the shirt front.
The brown S and green clovers are complete on the shirt front.
The finished shirt shows the logo at the wearer’s left chest.
The finished shirt shows the logo at the wearer’s left chest.