SEWTECHSupport Center 简体中文

Assemble the Stand and Mount the ST-1201 and SC-1501

Applies to ST-1201 / SC-1501 Demonstrated on ST-1201

Watch on YouTube ↗

Overview

Follow the ST-1201 demonstration to assemble the stand for the ST-1201 or SC-1501, fit the machine feet and thread rack, then lift the machine onto the four mounting pads. Have a second person ready for the lift and settle the stand on its four floor supports first.

Step-by-step guide

1. Lay out the parts and tools

Watch at 00:15

Set out two main frames, three support plates (one with the SEWTECH logo), one storage shelf, the screws and nuts, four round mounting pads and four leveling casters. Take the L-shaped hex key, open-end wrench and folding hex-key set from the toolbox. Keep the four machine feet ready for the underside of the machine.

The two main frames are at left. The shelf and toolbox are at right.
The two main frames are at left. The shelf and toolbox are at right.
One of the three support plates carries the SEWTECH logo.
One of the three support plates carries the SEWTECH logo.
The round pads come together in the small box.
The round pads come together in the small box.
Use the L-shaped hex key and open-end wrench for the caster hardware.
Use the L-shaped hex key and open-end wrench for the caster hardware.

2. Set both main frames upside down

Watch at 00:59

Set the two frames opposite each other. On each frame, the end plates with four caster holes face upward. At the floor end, turn the tabs with a single hole inward toward the space between the frames.

The demonstrator points to the upward-facing caster plate.
The demonstrator points to the upward-facing caster plate.
The single-hole tab at floor level points inward.
The single-hole tab at floor level points inward.

3. Fasten all four caster assemblies

Watch at 01:12

Seat a caster plate on each of the four corners. Swivel the wheel out of the way to reach the holes. Insert the screws from the plate side and start the nuts underneath by hand. Hold each nut with the open-end wrench while tightening the screw with the hex key. Repeat at all four corners and check each plate sits flat on the frame.

Swivel the red wheel to expose the holes in the square mounting plate.
Swivel the red wheel to expose the holes in the square mounting plate.
The screw passes down through the plate and the nut starts beneath it.
The screw passes down through the plate and the nut starts beneath it.
Hold the nut from below and tighten the screw from above.
Hold the nut from below and tighten the screw from above.
Repeat at the four corners while the frames are upside down.
Repeat at the four corners while the frames are upside down.

4. Start the first cross brace loosely

Watch at 02:22

Span the two upside-down frames with the first plain support plate near the caster end. Align the two holes at each end. Start all four screws by hand, then snug them lightly with the tools. Leave enough play between the frames to line up the shelf in the next step.

The first plain plate spans the frames. Two holes line up at each end.
The first plain plate spans the frames. Two holes line up at each end.
Hold the plate against the frame and start the screws by hand.
Hold the plate against the frame and start the screws by hand.
Snug the four screws lightly so the frame spacing can still change.
Snug the four screws lightly so the frame spacing can still change.

5. Align and secure the storage shelf

Watch at 02:57

Hold the shelf between the frames at the middle mounting holes. If a gap keeps the holes from lining up, nudge the two frames closer together or farther apart. Start the shelf screws by hand at the corners, then tighten them with the hex key. Once the shelf is seated, the video returns to the first brace and tightens it.

Support the shelf at both ends while lining it up with the center mounting holes.
Support the shelf at both ends while lining it up with the center mounting holes.
Move the frames slightly if the shelf does not reach both sets of holes.
Move the frames slightly if the shelf does not reach both sets of holes.
The hex key reaches the screw from inside the shelf lip.
The hex key reaches the screw from inside the shelf lip.
After the shelf is seated, finish tightening the first cross brace.
After the shelf is seated, finish tightening the first cross brace.

6. Fasten the two remaining support plates

Watch at 04:08

Keep the stand upside down. Fit the remaining plain plate across one open side and the logo plate across the opposite side. The logo faces outward and appears upside down at this point. Start the two screws at each end, then tighten the plates against the frames with the supplied tools.

Hold the remaining plain plate against the outer posts and start the screws at both ends.
Hold the remaining plain plate against the outer posts and start the screws at both ends.
The logo plate goes on the opposite side with the logo facing out.
The logo plate goes on the opposite side with the logo facing out.
Tighten the screws at both ends of the logo plate before turning the stand.
Tighten the screws at both ends of the logo plate before turning the stand.

7. Turn the completed frame upright

Watch at 05:14

With the shelf and plates secured, take one side of the stand each and turn it over together as shown. Set the four casters on the floor. The four single-hole tabs should now be at the top and the SEWTECH logo should read upright.

One person holds each side as the stand turns over.
One person holds each side as the stand turns over.
The casters are on the floor and the four pad tabs are at the top.
The casters are on the floor and the four pad tabs are at the top.

8. Install the four round mounting pads

Watch at 05:27

Fit one pad on each top tab, with the recessed cup facing upward. Pass the supplied flat-head screw down through the center and start the nut below the tab. Hold the nut with the open-end wrench and tighten from above with the hex key. Make sure all four cups sit flat on the tabs.

The inset shows the recessed face of the pad. Keep this face up.
The inset shows the recessed face of the pad. Keep this face up.
Use the flat-head screw and matching nut shown here.
Use the flat-head screw and matching nut shown here.
Drop the screw through the center of the pad and the stand tab.
Drop the screw through the center of the pad and the stand tab.
Hold the nut under the tab while tightening the screw from above.
Hold the nut under the tab while tightening the screw from above.

9. Install the feet under the machine base

Watch at 06:01

Before lifting the machine onto the stand, run the nuts down each foot's threaded stem toward the black foot pad to expose the threads. With a helper steadying the machine as shown, thread a foot into each of the four underside mounting points. Check that all four feet are fitted before lifting.

The nuts sit toward the black foot pad, leaving the end of the threaded stem exposed.
The nuts sit toward the black foot pad, leaving the end of the threaded stem exposed.
Turn the threaded stem into the mounting point under the machine base.
Turn the threaded stem into the mounting point under the machine base.
The side view shows the feet positioned beneath the base.
The side view shows the feet positioned beneath the base.

10. Lower the floor supports before mounting the machine

Watch at 06:26

Roll the empty stand to the installation spot. Turn the round support foot on each caster assembly down until it rests firmly on the floor and supports the stand. Repeat at all four corners, then check the stand does not rock or roll. If you need to move it later, raise the supports so the casters can roll again. Lower them again at the new location.

Turn the round foot beneath the caster bracket in the direction shown.
Turn the round foot beneath the caster bracket in the direction shown.
The black base of the support foot is firmly on the floor.
The black base of the support foot is firmly on the floor.
Repeat the same adjustment at the other corners.
Repeat the same adjustment at the other corners.
The demonstrator points to the support you retract to roll the stand.
The demonstrator points to the support you retract to roll the stand.

11. Find the four thread-rack rod positions

Watch at 07:27

Locate the four rod positions around the spool platform. On each metal rod, identify the spacer end and keep it facing down. Remove the screw from that end and keep it for the lower attachment.

The demonstrator points to the positions that the four rods will support.
The demonstrator points to the positions that the four rods will support.
The small spacer marks the lower end of each rod.
The small spacer marks the lower end of each rod.
Unscrew the bottom fastener by hand and set it aside for reinstallation.
Unscrew the bottom fastener by hand and set it aside for reinstallation.

12. Fasten the rods from under the spool platform

Watch at 07:46

Lift the white thread-guide cover clear of the spools. From below the lower spool platform, pass the screw upward through the mounting hole. Hold it from below while turning the rod onto it from above until the rod is secure. Repeat at the other three positions.

With the upper cover lifted, reach underneath the lower spool platform.
With the upper cover lifted, reach underneath the lower spool platform.
The lower screw is held beneath the plate while the rod is turned above it.
The lower screw is held beneath the plate while the rod is turned above it.
Reach under the platform again to fasten the last rod.
Reach under the platform again to fasten the last rod.

13. Refit the thread-guide cover and tighten it

Watch at 08:25

Remove the four screws from the tops of the rods. Lower the cover onto the rods and align its four mounting holes. Reinstall the screws through the cover with the fitting hex key. Start all four before fully tightening them, then check the cover is seated at every rod.

Remove the top screws before lowering the cover.
Remove the top screws before lowering the cover.
Hold the cover above the four rod ends and line up the holes.
Hold the cover above the four rod ends and line up the holes.
Insert the top screws through the cover with the hex key.
Insert the top screws through the cover with the hex key.
With all four screws started, finish tightening the cover.
With all four screws started, finish tightening the cover.

14. Lift from the base and seat all four feet

Watch at 09:38

Have two people lift the machine together, one on each side, using the grip points under the base shown in the inset. Lower it slowly so all four machine feet land in their matching round pads. Before letting go, check that each foot is centered and seated flat and that the stand stays still. The video ends with the machine seated on the stand.

The inset arrow points to the grip area beneath the machine base.
The inset arrow points to the grip area beneath the machine base.
Both people support the base as they bring the machine over the stand.
Both people support the base as they bring the machine over the stand.
A black machine foot lands in the white round mounting pad.
A black machine foot lands in the white round mounting pad.
The machine is seated on the assembled stand.
The machine is seated on the assembled stand.