Clear Trimmer Errors 26 and 40 on the ST-1501
Overview
On the SEWTECH ST-1501, EC40 means the trim cycle timed out. EC26 means the trimmer failed to return to its home position. The video shows how one thread nest can lead to both errors, then demonstrates how to clear the blockage, reset the moving knife and verify a clean trim.
Have small scissors, the Z-wrench shown in the video and a small cleaning brush ready. Stop the machine before reaching into the needle or bobbin area. Keep hands and tools clear whenever you operate the controls.
Step-by-step guide
1. Read the EC40 message
Watch at 00:14Read the dialog on the touchscreen. In the demonstration it displays “Err No = 40:cutLine TimeOut.” The upper-thread trimmer timed out before it completed its motion.


2. Look for a thread nest under the hoop
Watch at 00:28With the machine stopped, look under the hooped fabric and around the bobbin case below the needle plate. In the video, red thread has collected in both places. A nest in the knife path can keep the machine from cutting the thread or finishing the cycle.


3. Stop retrying the Trim command
Watch at 00:44The video shows the trimming mechanism hanging near the needle with the thread still attached. Leave the scissors icon on the touchscreen’s bottom row alone while the mechanism is blocked. Each press tries another trim and can produce an unusual sound.


4. Recognize EC26 after a failed return
Watch at 01:02The same obstruction can also produce “Err No = 26:Trimming not in position,” as shown on the touchscreen. The cycle may time out first and then report that the trimmer failed to return. Clear the trapped thread before attempting the reset.


5. Snip the threads holding the fabric
Watch at 01:31Use small scissors to snip the tangled threads between the underside of the fabric and the bobbin area. Free the fabric before moving the hoop so the thread cannot pull on the trimmer.


6. Remove the embroidery hoop
Watch at 01:36Support the hoop by its sides and free it from the mounting arms. Move the hoop and fabric clear of the needle head without catching them on the protruding trimmer.


7. Take out the bobbin case and lift away loose thread
Watch at 01:42Reach the bobbin case from the front beneath the needle plate. Hold its center latch and pull the case out. Gently lift the remaining loose or tangled threads out of the opening.



8. Remove the needle plate with the Z-wrench
Watch at 01:50The needle plate is the metal cover directly above the bobbin opening. Use the Z-wrench shown in the video to loosen its retaining screws, then lift the plate off to expose the knives.




9. Brush out lint and thread scraps
Watch at 01:58Use a small brush on the exposed cutting area above the bobbin opening. Brush away remaining strands, lint and fabric scraps from around the knives before resetting the mechanism.


10. Compare the moving knife with its home position
Watch at 02:05Locate the fixed and moving knives below the needle plate. The presenter points to the fixed knife first and then the moving knife. Compare the stuck position with the inset labeled “Correct Position” before using the reset control.



11. Use the 100° button and watch the knife return
Watch at 02:17With the obstruction cleared and hands and tools away, tap the 100° button at the far left of the touchscreen’s bottom row. In the video, a progress dialog appears briefly as the mechanism moves. Watch the trimmer retract near the needle and confirm that the exposed moving knife has returned to its home position.



12. Refit the needle plate and bobbin case
Watch at 02:30Once the movement has stopped and the knife is home, set the needle plate back over the cutting area and tighten the screws with the wrench. Then seat the bobbin case in its opening beneath the plate and close the cover.



13. Run a short embroidery test
Watch at 02:40Refit the hoop for a short test. In the video, the presenter starts stitching with the blue-ringed physical button below the touchscreen. Keep the needle and hoop area clear as the machine runs.


14. Verify a clean cut and a smooth return
Watch at 02:48Try Trim once after the short stitch run, as shown by the scissors icon in the video. Check that the thread cuts cleanly, the trimmer returns fully to its home position and neither EC26 nor EC40 appears on the touchscreen. If it stays out of position or either code returns, stop the test and consult the machine manual or SEWTECH support.

