SEWTECHSupport Center 简体中文

Reset a Needle Stuck Down on the ST-1501 and SC-1501

Applies to ST-1501 / SC-1501 Demonstrated on ST-1501

Watch on YouTube ↗

Overview

Use this procedure when the machine has stopped with a needle down and the controller shows a slashed 100° icon. Before using the powered reset, keep your hands clear of the needle, presser foot, and hoop. Leave the hoop in place while the needle is down.

Step-by-step guide

1. Check where the needle stopped

Watch at 00:07

Look at the active needle under the head. In the clip, it stays down close to the needle plate after the machine stops. If yours does the same, check the controller and leave the hoop in place while the needle is down.

The active needle is still down near the needle plate.
The active needle is still down near the needle plate.

2. Look for the slash on the 100° indicator

Watch at 00:15

Check the right side of the blue status bar at the top of the touchscreen. A slash through the circular 100° symbol means the main shaft is away from its 100° reference position.

The inset shows the slashed 100° indicator just to the left of the battery symbol.
The inset shows the slashed 100° indicator just to the left of the battery symbol.

3. Find the 100° reset button

Watch at 00:28

On the touchscreen shown, the reset button is at the far left of the lower blue toolbar, immediately to the left of the scissors icon. Use this lower button to reset the shaft.

The yellow arrow points to the 100° reset button at the left end of the toolbar.
The yellow arrow points to the 100° reset button at the left end of the toolbar.

4. Tap 100° and wait for the shaft to reset

Watch at 00:34

Tap the lower 100° button once. Keep clear of the head while the controller displays “The machine is in action, please wait…” and a progress bar. Wait for the movement to finish.

The demonstrator taps the leftmost button in the lower toolbar.
The demonstrator taps the leftmost button in the lower toolbar.
The message and progress bar show the reset is in progress.
The message and progress bar show the reset is in progress.

5. Confirm the needle is up and the slash has cleared

Watch at 00:38

Watch the needle rise clear of the needle plate. Then check the top status bar again. The circular 100° symbol should be visible without a slash. If either check fails, leave embroidery stopped.

At the start of the close-up, the needle tip is still at the plate.
At the start of the close-up, the needle tip is still at the plate.
The needle rises and leaves a visible gap above the plate.
The needle rises and leaves a visible gap above the plate.
The 100° symbol remains visible. The diagonal slash is gone.
The 100° symbol remains visible. The diagonal slash is gone.

6. Open the manual needle selector

Watch at 00:54

After the needle is up and the 100° status is clear, tap the three-needle icon in the bottom toolbar, just to the right of the scissors. The controller opens a panel with the 15 needle numbers.

Tap the three-needle icon, the third button from the left in the lower toolbar.
Tap the three-needle icon, the third button from the left in the lower toolbar.
The needle selector opens with needle 7 highlighted in this example.
The needle selector opens with needle 7 highlighted in this example.

7. Select a different needle to complete the color change

Watch at 00:56

Tap the needle number for the color you need and wait for the head to finish shifting. Check that the new number is highlighted. The video changes from needle 7 to needle 5 as an example.

The demonstrator selects a new number in the grid.
The demonstrator selects a new number in the grid.
Needle 5 is now highlighted after the head shifts to the selected position.
Needle 5 is now highlighted after the head shifts to the selected position.

8. Return to the controller’s main view

Watch at 00:59

Use the return icon at the lower right of the needle selector, just above the blue toolbar. Check that the needle grid closes and the main controls are visible again.

The fingertip presses the pale return button above the blue toolbar.
The fingertip presses the pale return button above the blue toolbar.
The needle grid has closed and the main controls are back.
The needle grid has closed and the main controls are back.

9. Resume embroidery and check the first stitches

Watch at 01:01

Once the needle has lifted, the 100° slash has cleared, and the selected needle is in position, resume embroidery. Watch the first stitches and check that the needle cycles normally. The video cuts to stitching a letter F in a round hoop.

The final demonstration uses a round hoop with a partly stitched letter F.
The final demonstration uses a round hoop with a partly stitched letter F.
The active needle is working over the hooped design after the reset.
The active needle is working over the hooped design after the reset.