Create Custom Lettering on the ST-1501
Overview
Create and save a name as an embroidery design on the ST-1501 touchscreen. The video starts with the machine connected to Wi-Fi and points to its description for Wi-Fi setup. Have the exact wording ready and know which hoop and thread color you will use before stitching.
Step-by-step guide
1. Open the lettering tool
Watch at 00:24On page 1 of the controller, tap T in the lower row of icons, just above the blue bottom bar. The lettering editor opens with an empty preview above the editing controls.


2. Choose a language and font
Watch at 00:28Tap the wide language and font button directly below the preview. For the example, choose the UK flag for English, then tap Arial Rounded. Check that the flag and font name appear together on the editor button.


3. Enter the name on the keyboard
Watch at 00:38Tap the small keyboard toggle at the right end of the dimensions strip. Enter the wording using the on-screen keys. The example builds the name Claire in the preview above the keyboard. Check the spelling and capitalization before changing the layout.


4. Undo the last edit
Watch at 00:48Use the orange curved arrow beside the font selector to reverse the last edit. In the example, Claire becomes Clair. Use the keyboard to re-enter the final e if you want to restore it.


5. Set text alignment
Watch at 00:55Tap the stacked horizontal lines on the left of the editing controls to cycle through the alignment choices. Watch the lettering above and stop when it aligns as intended.

6. Set character size and read the overall dimensions
Watch at 01:05Tap the A with the vertical double arrow. Enter the character size in millimeters on the number pad, then tap the check mark. The maximum shown is 50 mm. Read Width and Height under the preview for the whole design. At a character size of 50 mm, Claire measures about 165.6 × 60.9 mm in this editing preview.



7. Choose a color for the editing preview
Watch at 01:22Tap the colored square next to the size button and choose a swatch. The video changes the lettering on screen from blue to pink. Assign the actual needle and thread color after opening the saved design.


8. Switch between straight, vertical and curved lettering
Watch at 01:40Tap the line or curve icon in the wide control at the bottom left. It cycles through layouts, including straight horizontal text, vertical text and curved baselines. Check the preview as you switch. This control changes how the letters are arranged; the stacked-lines button above controls alignment.



9. Adjust the baseline radius and check legibility
Watch at 01:50With a curved layout selected, tap the baseline radius value and enter a new value in millimeters. Tap the check mark and look at the curve, letter spacing and dimensions. The video changes the radius from 100 to 30 mm. One later layout with a 50 mm baseline length makes the letters overlap. The final example returns to a straight horizontal line before generating stitches.



10. Generate and inspect the stitches
Watch at 02:08Check the wording, font, alignment, size, preview color and layout, then tap the large S near the lower right. Wait for processing to finish and for the stitch preview to appear. Verify spelling, spacing and the generated dimensions again. In the example, the generated design measures about 199.9 × 53.9 mm.



11. Save the pattern in machine memory
Watch at 02:22Tap the floppy disk icon to the right of S. In Data Import, enter Pattern Num and Pattern Name, then confirm with the check mark. Look for “Import pattern success!” Tap the left button in that message to return to page 1 and check that the saved entry is listed. The example uses pattern number and name 558.




12. Select the saved design and assign the needle
Watch at 02:45Select the saved entry on page 1, then open the third tab for the color sequence. Select the needle position carrying the thread you want and verify the assigned color on the left. The saved Claire preview turns green in this example.


13. Position the design and trace its border
Watch at 02:51Open the hoop-positioning tab next to the color tab. Match the on-screen hoop to the hoop fitted to the machine. Use the directional controls to place the design inside the hoop outline. Tap the dashed-rectangle trace icon at the upper middle of the left control group. The movement prompt asks you to check the cap frame and remove it if necessary. Confirm only when the frame can move freely. Watch the full trace to check that the needle path stays safely inside the hoop before stitching.


