Assemble the ST-1501 Stand and Mount the Machine
Overview
Assemble the wheeled stand, fit the thread guide to the ST-1501, then mount the machine. Arrange for a second person to help turn the stand and lift the machine.
Step-by-step guide
1. Lay out the parts and tools
Watch at 00:17Set out the two main frames, two slotted side support plates, storage shelf, four caster assemblies, four machine mounting pads, and fasteners. Get the Allen wrench and adjustable wrench from the toolbox. Set aside the four metal thread-guide rods for the work on the machine.
2. Orient the frames for the casters
Watch at 00:45Set both main frames upside down with the sides that have the large holes facing up. Locate the four corners where the caster plates will sit.
3. Fit and tighten all four casters
Watch at 01:02Place a caster at a corner and swivel the wheel slightly for access to the screw holes. Start the screws by hand, then fully tighten them with the Allen wrench. Repeat at the other three corners. Check that all four plates sit flush against the frames.
4. Align and fasten the storage shelf
Watch at 02:05Keep the casters facing up. Hold the shelf between the two frames and bring the shelf and frame holes together. Hand-start the shelf screws as shown, then snug them lightly with the Allen wrench. Once all four are in, fully tighten them.
5. Fasten both side support plates
Watch at 03:09Hold one slotted support plate across an open side of the stand. Match its four corner holes to the holes in the frames and start all four screws by hand. Tighten them with the Allen wrench once the plate sits in place. Fit the plate on the opposite side the same way.
6. Turn the stand upright
Watch at 04:07With the shelf and both plates secured, have two people grip opposite sides and turn the empty stand over as shown. Set it down with all four casters underneath and the two machine-mounting rails on top.
7. Install the four thread-guide rods
Watch at 04:26Fit the rods to the machine before lifting it onto the stand. Identify the spacer end of each rod and keep it down. Remove the screw from that end. Have a helper lift the guide plate enough to clear the work area. Insert the screw upward through the mounting plate below the thread cones, then spin the rod onto it by hand. Repeat at all four positions and tighten the lower screws with the Allen wrench.
8. Secure the thread guide plate
Watch at 05:15Remove the four screws from the tops of the rods. Lower the guide plate onto the rods and align the four holes. Insert the saved screws through the plate and tighten them with the Allen wrench. Check that the plate sits on all four rods.
9. Lower the four leveling feet
Watch at 06:17Roll the empty stand into its working position. Turn down the round threaded foot next to each caster until it bears firmly on the floor. Check all four corners before loading the stand. The feet should carry the stand so it stays put. To roll it again later, turn the feet up until the casters can carry the stand.
10. Align the four mounting pads with the outer holes
Watch at 06:55Lay one pad flat on each upper corner of the stand. Each corner has two holes. Center the pad over the hole closest to the end of the rail, as shown by the arrow. Check the position of all four pads before lifting the machine.
11. Lift the machine onto the stand
Watch at 07:09With a second person, support the machine from the underside of its base as shown. Lift it over the stand and lower it carefully onto the four pads. Align the holes in the bottom of the machine base with the holes through the pads and stand. Check that the feet of the machine base sit squarely on the pads.
12. Start all four mounting bolts from below
Watch at 07:43Use the four machine mounting bolts with the spacer and washer shown in the close-up. Reach under the top rail at each corner and insert the bolt upward into the aligned mounting hole. Start each bolt by hand. Check that all four have engaged before tightening with the wrench.
13. Tighten the bolts and check the assembly
Watch at 08:15Use the adjustable wrench from under the stand to fully tighten all four machine mounting bolts. Before using the machine, check that the base sits on the pads, each bolt is tight, and all four leveling feet bear firmly on the floor. Finish with the stand steady in its working position.