SEWTECHSupport Center 简体中文

Transfer Embroidery Designs over Wi-Fi on the ST-1501

Applies to ST-1501

Watch on YouTube ↗

Overview

Have the ST‑1501 controller on its design screen, a Windows PC, the password for a shared 2.4 GHz Wi‑Fi network, the SEWTECH transfer package and an embroidery design file ready. The video uses the A15 interface and a .DST design. The transfer is confirmed by a success message on the PC and a new entry in the controller’s design list.

Step-by-step guide

1. Connect the Windows PC to 2.4 GHz Wi‑Fi

Watch at 00:13

Open the Wi‑Fi list from the Windows taskbar. Select the 2.4 GHz network you will also use on the ST‑1501 and click Connect. Wait for Windows to show Connected. The video switches from WG-5G to WG-2.4G. Use the 2.4 GHz network name for your own setup.

The Windows Wi‑Fi panel shows the 2.4 GHz entry and its Connect button.
The Windows Wi‑Fi panel shows the 2.4 GHz entry and its Connect button.
The status under the selected network changes to Connected, secured.
The status under the selected network changes to Connected, secured.

2. Choose the same network on the ST‑1501

Watch at 00:19

On the controller’s design screen, tap the Wi‑Fi symbol in the blue bar at the top. In Wireless Local Area Network, select the same 2.4 GHz network used by the PC and tap Connect beside its name. The ST‑1501 in the video uses 2.4 GHz. If your router lists separate bands, choose the 2.4 GHz entry.

The fingertip is on the Wi‑Fi icon in the top blue bar.
The fingertip is on the Wi‑Fi icon in the top blue bar.
The selected network row is highlighted and has its own Connect button.
The selected network row is highlighted and has its own Connect button.

3. Enter the Wi‑Fi password and check the connection

Watch at 00:25

Use the controller’s on-screen keyboard to enter your network password and tap the check mark on the keyboard to submit it. Wait for Connecting… to clear and look for the check mark beside the intended network in the list. That mark is the connection feedback shown in the video.

The on-screen keyboard appears after Connect. Its check mark submits the password.
The on-screen keyboard appears after Connect. Its check mark submits the password.
The controller shows Connecting while it attempts to join the network.
The controller shows Connecting while it attempts to join the network.
The presenter points to the check marks in the network list. Check the mark beside your own network.
The presenter points to the check marks in the network list. Check the mark beside your own network.

4. Open More Set on the controller

Watch at 00:56

From the design screen, tap the hand icon at the far right of the bottom blue bar. In the settings grid, choose More Set, the worker-and-gear icon in the center. On the Number Pad, enter the controller settings code and tap the blue check mark. The video shows 823456 for the controller used in the demonstration.

The bottom-right hand icon opens the settings grid.
The bottom-right hand icon opens the settings grid.
More Set is the center tile in the grid.
More Set is the center tile in the grid.
Enter the controller settings code in the Number Pad.
Enter the controller settings code in the Number Pad.

5. Select Mac. Config and enable Start DHCP

Watch at 01:06

Tap the list button at the lower left of the parameter screen. Choose Mac. Config, then find Start DHCP on row 7 below DNS Server. If it reads no, tap the green ON button and confirm it reads yes. The video briefly shows 0.0.0.0 in the address fields after the change. Leave the fields to DHCP and use the online machine list in A15 to check the connection. Return to the design screen before sending.

Use the list button at the lower left to open the parameter categories.
Use the list button at the lower left to open the parameter categories.
Mac. Config is the highlighted item in the category list.
Mac. Config is the highlighted item in the category list.
Before enabling DHCP, the Start DHCP row reads no.
Before enabling DHCP, the Start DHCP row reads no.
After tapping the green ON control, the row reads yes.
After tapping the green ON control, the row reads yes.

6. Extract the SEWTECH transfer package

Watch at 01:21

On the Windows PC, locate your downloaded SEWTECH Wi‑Fi design transfer package. Open the archive, select the package folder and extract it to a location you can find in File Explorer. The narration calls it a ZIP file and the demonstrated archive ends in .rar. Open the extracted copy after unpacking.

Select the folder inside the transfer software archive.
Select the folder inside the transfer software archive.
Choose the extraction destination and confirm with OK.
Choose the extraction destination and confirm with OK.
The extracted folder is now visible in File Explorer.
The extracted folder is now visible in File Explorer.

7. Run VC_RedistInstaller and complete setup

Watch at 01:36

Open SEWTECH A15 PRO System Files within the extracted package and double-click VC_RedistInstaller. In the VC Redist Installer Setup Wizard, click Next, follow the component and installation screens, and wait until the completion screen appears. Click Finish to close the installer.

File Explorer highlights VC_RedistInstaller in SEWTECH A15 PRO System Files.
File Explorer highlights VC_RedistInstaller in SEWTECH A15 PRO System Files.
Continue from the Select Components screen with Next.
Continue from the Select Components screen with Next.
The completion screen confirms setup has finished. Click Finish.
The completion screen confirms setup has finished. Click Finish.

8. Launch the Wi‑Fi transfer utility

Watch at 01:51

Go back to the package folder in File Explorer and open the Wi-Fi transfer folder, spelled Wifi deisgn transfer in the demo. Double-click the SEWTECH A15 PRO application. In the blue A15 window, check the left column labeled Machine on line for your controller. The IP address in the video belongs to the demonstration network.

Open the transfer folder shown in the address bar and launch SEWTECH A15 PRO.
Open the transfer folder shown in the address bar and launch SEWTECH A15 PRO.
Machine on line lists the online controller with a checked entry.
Machine on line lists the online controller with a checked entry.

9. Load the embroidery file with Input Design

Watch at 01:56

Click Input Design at the left end of the bottom button row in A15. Browse to your embroidery design folder in the Open dialog, select the file and click Open. The video uses a .DST file. Check the drawing in Design Show before sending it.

Input Design opens the embroidery file picker.
Input Design opens the embroidery file picker.
Select the intended .DST file and confirm with Open.
Select the intended .DST file and confirm with Open.
Design Show previews the loaded flower design before transfer.
Design Show previews the loaded flower design before transfer.

10. Send Current Design and check the PC message

Watch at 02:05

With the intended design previewed and your controller listed online, click Send current Design along the bottom of A15. Wait for “Successful sending of Design!” and dismiss the message with OK.

The Send current Design button is third from the left on the bottom row.
The Send current Design button is third from the left on the bottom row.
The dialog reads “Successful sending of Design!” despite the yellow icon.
The dialog reads “Successful sending of Design!” despite the yellow icon.

11. Find the new design on the machine

Watch at 02:13

Check the thumbnails on the ST‑1501 controller. In the demo, the transferred design appears in the far-right tile of the top row. Match the name of the new entry to the file you sent. This example shows flower woman. Its small green thumbnail on the controller looks different from the large color preview on the PC. The video ends with the design visible in the controller library.

The arrow points to the new green thumbnail on the machine. The PC still shows its color preview.
The arrow points to the new green thumbnail on the machine. The PC still shows its color preview.
On the controller, the new tile and its name are visible in the design list.
On the controller, the new tile and its name are visible in the design list.