SEWTECHSupport Center 简体中文

Import Machine and Driver Parameters on the ST-1501

Applies to ST-1501

Watch on YouTube ↗

Overview

This ST-1501 procedure imports More Set, Frame and Driver Param Load from a machine-specific USB file. Proceed under the guidance of SEWTECH technical support or an authorized technician. Confirm the file and the three selections with them. Wait for “import param data success” before returning to the main screen and removing the drive.

Step-by-step guide

1. Prepare the approved parameter file

Watch at 00:12

Have SEWTECH technical support or an authorized technician confirm the parameter file for your specific ST-1501 and guide the import. The presenter instructs you to put only the approved parameter file on the USB drive. An incorrect file or selection can trigger a machine error.

Start from the main screen with the approved file ready on a USB drive.
Start from the main screen with the approved file ready on a USB drive.

2. Insert the USB drive

Watch at 00:18

Plug the drive into the port on the right edge of the controller while the design thumbnails are visible on the main screen. Leave it connected through the import.

Line up the USB plug with the port on the right edge of the controller.
Line up the USB plug with the port on the right edge of the controller.
The drive stays connected while the controller is on the main screen.
The drive stays connected while the controller is on the main screen.

3. Open Other Functions

Watch at 00:25

Tap the gear at the far right of the bottom blue toolbar. The main screen switches to a grid of functions.

The arrow points to the Other Functions gear at the far right of the toolbar.
The arrow points to the Other Functions gear at the far right of the toolbar.
The gear opens the function grid. Debug is in the left column, second row.
The gear opens the function grid. Debug is in the left column, second row.

4. Open Debug and confirm access

Watch at 00:29

Tap Debug, the wrench-and-screwdriver icon in the second row on the left. Enter the service password your technician confirms for this controller. Tap the large blue check mark on the keypad to open the numbered Debug menu.

The wrench-and-screwdriver tile is labeled Debug.
The wrench-and-screwdriver tile is labeled Debug.
The large blue check mark beneath the numbers submits the service password.
The large blue check mark beneath the numbers submits the service password.

5. Open Param(+driver) Import/Export

Watch at 00:38

On page 1/2 of Debug, tap item 9, Param(+driver) Import/Export, immediately above Reset Param. The next screen has five entries, with Param Import at the top.

The red outline in the video marks item 9, just above Reset Param.
The red outline in the video marks item 9, just above Reset Param.
Param Import and Param Export are the first two rows of the submenu.
Param Import and Param Export are the first two rows of the submenu.

6. Open Param Import

Watch at 00:44

Tap Param Import at the top. The file browser opens, with the list above the highlighted USB device icon in the bottom bar.

The presenter points to Param Import, the first entry.
The presenter points to Param Import, the first entry.
The file list is above the blue USB device icon in the bottom bar.
The file list is above the blue USB device icon in the bottom bar.

7. Select the approved file

Watch at 00:47

Tap the row for the file approved for your machine. The demonstration uses paramData.dpdv2. Check the filename provided by your technician.

The red box identifies the example file row. The inset shows its filename.
The red box identifies the example file row. The inset shows its filename.

8. Confirm the file with the first check mark

Watch at 00:51

Tap the check mark in the file browser’s bottom bar, immediately left of the exit icon. This opens a new dialog for selecting which parameter categories to import.

The blue check mark immediately left of the exit icon confirms the selected file.
The blue check mark immediately left of the exit icon confirms the selected file.
The controller opens a separate dialog with four categories.
The controller opens a separate dialog with four categories.

9. Verify the three import categories

Watch at 00:53

For this service-approved import, verify that More Set, Frame and Driver Param Load are all checked. They are already checked when the dialog opens in the video. Leave the fourth box, Stitch Color Setting, empty as shown.

The overlay names the three categories used for this import.
The overlay names the three categories used for this import.
The top three boxes contain red checks. Stitch Color Setting, at the bottom, is empty.
The top three boxes contain red checks. Stitch Color Setting, at the bottom, is empty.

10. Start the import with the second check mark

Watch at 01:05

After verifying the three choices, tap the blue check mark at the lower right of the category dialog. The dialog closes. Keep the USB drive connected while the controller imports the parameters and wait for its success message.

The check mark inside the category dialog starts the import.
The check mark inside the category dialog starts the import.
The parameter submenu is visible again while the USB drive stays connected.
The parameter submenu is visible again while the USB drive stays connected.

11. Verify the success message

Watch at 01:10

Wait for the Information dialog to read “import param data success”. If the controller reports an error or the success message never appears, check with the technician before repeating the import.

The Information dialog confirms “import param data success”.
The Information dialog confirms “import param data success”.

12. Close the message and return to the main screen

Watch at 01:15

Tap the exit icon in the lower right of the success dialog. Then use the lower-right exit icon on each screen to leave the parameter submenu, the numbered Debug menu and the Other Functions grid. Check that the design thumbnails and main controls are visible again.

The small door icon closes the success message.
The small door icon closes the success message.
The parameter submenu has its own exit button at the bottom right.
The parameter submenu has its own exit button at the bottom right.
Use the lower-right exit again on the numbered Debug menu.
Use the lower-right exit again on the numbered Debug menu.
The presenter uses the exit icon on the Other Functions grid.
The presenter uses the exit icon on the Other Functions grid.
The design thumbnails are back on the main screen.
The design thumbnails are back on the main screen.

13. Remove the USB drive

Watch at 01:21

Once the main screen is back, pull the USB drive out of the right-side port. The main screen remains visible after removal.

With the main screen visible, the presenter grips the drive at the right edge.
With the main screen visible, the presenter grips the drive at the right edge.
The USB drive is removed and the controller remains on the main screen.
The USB drive is removed and the controller remains on the main screen.