SEWTECHSupport Center 简体中文

Set the 8-in-1 Hoop Center on the ST-1501

Machine ST-1501 8-in-1 magnetic hoop set

Watch on YouTube ↗

Before you begin

Have a piece of stabilizer and a washable fabric pen ready. The video shows how to set and verify the center for the 7 × 5 and R6 hoops. Once each profile is set, the laser should return to the marked center when you select that hoop.

The marked center of the installed hoop and the selected profile on the control panel.
The marked center of the installed hoop and the selected profile on the control panel.

Hoop center setup

1. Mark the physical center

Watch at 00:18 ↗

Secure a piece of stabilizer in the magnetic hoop. Keep your fingers clear as the hoop closes. Use the built-in center marks and a washable fabric pen to draw one vertical line and one horizontal line. The intersection marks the physical center of the hoop.

Stabilizer held in the magnetic hoop.
Stabilizer held in the magnetic hoop.
The two guide lines meet at the physical center.
The two guide lines meet at the physical center.

2. Mount the hoop on the adapter

Watch at 00:50 ↗

Loosen the adjustment knob and align the three mounting holes on the hoop with the three slots on the adapter. Seat the center hole all the way to the top of its slot so there is no gap. Tighten the knob and check that the hoop is secure.

Loosen the knob before fitting the hoop.
Loosen the knob before fitting the hoop.
Check that the center mounting hole is seated fully.
Check that the center mounting hole is seated fully.

3. Check the laser and select needle 1

Watch at 01:17 ↗

Before installing the hoop, verify that the laser point lines up with the center of the needle plate hole. Install the hoop and check that both hoop arms are firmly seated. Select needle 1 on the control panel before setting the hoop position.

The circled area is the reference point at the needle plate.
The circled area is the reference point at the needle plate.
Check that both hoop arms are secured to the machine.
Check that both hoop arms are secured to the machine.

4. Select the hoop and align the laser

Watch at 01:46 ↗

Open the hoop selection page and select the profile for the hoop installed on the machine. The first example uses the 7 × 5 hoop. Open the frame parameter page and use the movement arrows to place the laser directly over the intersection marked on the stabilizer.

Open the hoop selection page on the control panel.
Open the hoop selection page on the control panel.
The movement arrows shift the hoop toward the marked crosshair.
The movement arrows shift the hoop toward the marked crosshair.

5. Add the X and Y offsets

Watch at 02:33 ↗

Read the signed X and Y movement offsets shown on the screen. For each axis, add the offset to the current value in its field. In the 7 × 5 example from the video, X is 156 + 1 = 157 and Y is −58 + (−25) = −83. Enter the results calculated from the readings on your screen, then tap the check mark and confirm.

7 × 5 example. Add the X offset of +1 to the existing value of 156.
7 × 5 example. Add the X offset of +1 to the existing value of 156.
7 × 5 example. The Y offset of −25 added to −58 gives −83.
7 × 5 example. The Y offset of −25 added to −58 gives −83.

6. Reselect the 7 × 5 hoop to verify

Watch at 03:39 ↗

Switch to a different hoop profile, then reselect 7 × 5. After the frame moves into position, check that the laser returns to the marked intersection. This verifies the saved center for that hoop.

The video switches hoop profiles before checking the saved center.
The video switches hoop profiles before checking the saved center.
Reselect 7 × 5 and check the laser against the crosshair.
Reselect 7 × 5 and check the laser against the crosshair.

7. Repeat the setup for R6

Watch at 04:06 ↗

Mark the center of R6, install it securely, and select its profile. Repeat the same alignment and offset calculation for this hoop. In the R6 example from the video, X is 156 + 2 = 158 and Y is −67 + (−28) = −95. Confirm the new values, switch to another profile, then reselect R6 and check that the laser returns to the crosshair.

Use the built-in marks to find the physical center of R6.
Use the built-in marks to find the physical center of R6.
Choose the R6 hoop profile on the control panel.
Choose the R6 hoop profile on the control panel.
R6 example. The existing Y value of −67 plus the offset of −28 gives −95.
R6 example. The existing Y value of −67 plus the offset of −28 gives −95.
After reselecting R6, the laser returns to the marked center.
After reselecting R6, the laser returns to the marked center.
This guide is based on the original SEWTECH TV footage and YouTube’s automatic English captions. Image timestamps mark the frames shown. Each step’s video link starts at the beginning of that segment.