SEWTECHSupport Center 简体中文

Use and Reset the ST-1501 Emergency Stop

Applies to ST-1501

Watch on YouTube ↗

Overview

Follow the SEWTECH ST-1501 demonstration from plugging in and powering on through engaging the emergency stop, resetting it, and shutting down. The main rocker is on the back of the machine base. The red emergency stop sits just behind the top of the touchscreen.

The video calls out 100–240 V. The ST-1501 product specifications list AC 110–230 V. Before connecting power, follow the input rating on your own machine’s nameplate and the instructions supplied with it.

Step-by-step guide

1. Locate the rear power inlet and switch

Watch at 00:11

With the cord disconnected, find the power panel on the back of the machine base. The black rocker switch is on the left and the power inlet is on the right. Set the rocker to O (off) and have the machine’s power cord ready.

The rear power panel groups the rocker switch and the empty power inlet on one plate.
The rear power panel groups the rocker switch and the empty power inlet on one plate.
The yellow 100–240 V callout is the figure stated in the video. Check the rating on your own unit before connecting it.
The yellow 100–240 V callout is the figure stated in the video. Check the rating on your own unit before connecting it.

2. Connect the power cord

Watch at 00:27

With the rear switch still at O, seat the machine end of the cord in the rear inlet. Then plug the other end into a grounded outlet that matches the machine’s input rating. The video shows the wall-plug end going into a power strip.

The arrow points to the machine-end connector entering the inlet beside the rear switch.
The arrow points to the machine-end connector entering the inlet beside the rear switch.
The demonstrator seats the other end in the outlet shown in the video.
The demonstrator seats the other end in the outlet shown in the video.

3. Turn on the rear switch and wait for startup

Watch at 00:42

Press the I (on) side of the rear rocker beside the connected cord. The touchscreen lights up and shows the startup screens. Wait for the design screen with pattern thumbnails to confirm that the controller has finished starting.

Press the upper I side of the black rear rocker beside the cord.
Press the upper I side of the black rear rocker beside the cord.
The SEWTECH splash screen confirms the controller has begun to boot.
The SEWTECH splash screen confirms the controller has begun to boot.
The pattern thumbnails appear after the startup screens clear.
The pattern thumbnails appear after the startup screens clear.

4. Find the red emergency stop

Watch at 00:49

Look just behind the top edge of the touchscreen for the small red physical button. From the front you can see its red cap above the controller.

The arrow identifies the red emergency-stop cap just above the touchscreen.
The arrow identifies the red emergency-stop cap just above the touchscreen.

5. Press straight down in an emergency

Watch at 01:00

Press the red button straight down immediately when you need to stop machine movement. It stays latched down after you remove your hand. On the unit shown, the touchscreen goes dark after the press.

The downward arrow shows where and how to press the red cap.
The downward arrow shows where and how to press the red cap.
After the press, the hand is off the button and the touchscreen has gone dark.
After the press, the hand is off the button and the touchscreen has gone dark.

6. Recognize a startup blocked by the emergency stop

Watch at 01:13

If the machine stays off after you use the rear switch, check whether the red emergency stop is still latched down. In the video, the power cord remains connected and the rear switch is pressed, but the touchscreen stays dark while the stop is engaged.

The close-up shows the rear switch being pressed. The inset shows the controller still dark.
The close-up shows the rear switch being pressed. The inset shows the controller still dark.
The screen remains dark after the hand moves away from the rear switch.
The screen remains dark after the hand moves away from the rear switch.

7. Release the stop by turning it clockwise

Watch at 01:27

Once the cause of the stop has been addressed and the machine area is clear, turn the red cap clockwise until it pops up. Check that the cap stays raised when you let go. In the video, the screen stays dark at this point.

Turn the red cap in the clockwise direction shown by the curved arrow.
Turn the red cap in the clockwise direction shown by the curved arrow.
The hand has released the raised cap. The touchscreen is still dark.
The hand has released the raised cap. The touchscreen is still dark.

8. Power back on and confirm the design screen

Watch at 01:37

Press I on the rear rocker again. In the video, the controller shows the A15-pro startup screen and returns to the design thumbnails. Use that return as the startup check. Before continuing embroidery, confirm the area is safe and check the job on your machine.

The inset shows the demonstrator using the rear switch again after releasing the red stop.
The inset shows the demonstrator using the rear switch again after releasing the red stop.
A15-pro is the startup screen seen on the demo controller.
A15-pro is the startup screen seen on the demo controller.
The design thumbnails are back. This is the final restart check shown in the video.
The design thumbnails are back. This is the final restart check shown in the video.

9. Turn off the machine at the rear switch

Watch at 01:51

When embroidery is finished and the machine has stopped, press the O (off) side of the rear rocker. Check that the touchscreen goes dark before unplugging the cord.

The inset shows the hand at the rear rocker while the touchscreen is still lit.
The inset shows the hand at the rear rocker while the touchscreen is still lit.
After the rear switch is turned off, the touchscreen is dark and the cord is still connected.
After the rear switch is turned off, the touchscreen is dark and the cord is still connected.

10. Unplug at the outlet

Watch at 01:55

After switching off, grasp the plug body at the outlet and pull the plug out. Check that it is fully clear of the socket.

Grip the outlet-end plug by its body before pulling it free.
Grip the outlet-end plug by its body before pulling it free.
The outlet is empty and the plug is free in the demonstrator’s hand.
The outlet is empty and the plug is free in the demonstrator’s hand.