SEWTECHSupport Center 简体中文

Troubleshoot Thread Breaks on the ST-1501

Applies to ST-1501

Watch on YouTube ↗

Overview

Use this guide when the thread has actually broken on the SEWTECH ST-1501. Work from the bobbin and needle to the full upper-thread path, then check the feed at the needle before resuming.

Have a wound bobbin and a small flat-blade screwdriver ready if you need to adjust the bobbin case.

Step-by-step guide

1. Check how much bobbin thread is left

Watch at 00:31

Stop the ST-1501 before working near the needles or hook. The bobbin case sits in the hook opening beneath the needle row. Flip down the cover, pull the case out by its latch and check the bobbin. If it is empty, replace it with the fully wound bobbin, then bring the thread out through the case as shown.

With the cover flipped down, pull the silver bobbin case forward by its latch.
With the cover flipped down, pull the silver bobbin case forward by its latch.
The wound bobbin is held above the open case before insertion.
The wound bobbin is held above the open case before insertion.
The thread tail comes out through the side of the case after the new bobbin is fitted.
The thread tail comes out through the side of the case after the new bobbin is fitted.

2. Hang the bobbin case for a drop test

Watch at 00:50

Hold the exposed bobbin thread between your fingers so the loaded case hangs freely. Keep your other palm underneath to catch it and give the thread a short flick. If the case stays in place or only creeps down even with a firmer shake, the bobbin tension is too tight.

Hold only the thread and leave room beneath the suspended case.
Hold only the thread and leave room beneath the suspended case.
During the tight-tension example, watch for very little thread feeding out despite the shake.
During the tight-tension example, watch for very little thread feeding out despite the shake.

3. Loosen the larger screw a little at a time

Watch at 00:58

If the drop test shows excessive tension, hold the bobbin case out of the machine. Place the screwdriver in the larger tension screw on the side of the case and turn it counterclockwise about 1/10 to 1/8 of a turn. Test again after each adjustment and repeat in small increments if needed.

The screwdriver engages the larger screw. The overlay shows the direction and amount for one adjustment.
The screwdriver engages the larger screw. The overlay shows the direction and amount for one adjustment.
Use a small turn at the screw so you can test the effect before making another adjustment.
Use a small turn at the screw so you can test the effect before making another adjustment.

4. Retest for a short, controlled drop

Watch at 01:20

Suspend the case again and use a gentle wrist flick. The video's target is a smooth drop of about 3–5 cm (roughly 1–2 in), followed by the case stopping by itself. Leave enough clearance above your catching hand to see whether the case stops on its own. Refit the loaded case before returning to stitching.

The case is suspended above the palm, leaving a gap so you can observe the drop.
The case is suspended above the palm, leaving a gap so you can observe the drop.
The presenter catches the case in this shot. The stated test is for the case to stop on its own before it touches your hand.
The presenter catches the case in this shot. The stated test is for the case to stop on its own before it touches your hand.

5. Turn the long groove toward you

Watch at 01:33

Examine the needle at the front of the needle row. The long groove faces forward, toward you. The scarf, the shallow recess near the eye, faces the back, toward the machine. Use the front and back views in the video to identify the two sides before seating the needle.

The arrow identifies the needle area beneath the row of needle bars.
The arrow identifies the needle area beneath the row of needle bars.
The overlay distinguishes the long groove on the front from the scarf near the eye on the back.
The overlay distinguishes the long groove on the front from the scarf near the eye on the back.

6. Seat the needle all the way up

Watch at 01:53

With the needle facing the correct way, slide its shank straight up into the needle bar until fully seated. Hold it in that position and tighten the needle clamp screw. Before embroidering, check that the needles are correctly seated and oriented. The upward arrow identifies the direction of insertion.

The sideways arrow singles out the needle being checked under the bar.
The sideways arrow singles out the needle being checked under the bar.
The upward arrow marks where to seat the needle. The screwdriver is at the clamp screw above it.
The upward arrow marks where to seat the needle. The screwdriver is at the clamp screw above it.
Look along the row to verify the other needles before embroidering.
Look along the row to verify the other needles before embroidering.

7. Pull the upper thread gently to feel for a snag

Watch at 02:18

With the machine stopped, take the upper-thread tail at the needle end and pull it gently by hand. If it feels tight, catches repeatedly or will not feed smoothly, follow the same thread back from the needle to the spool to find the snag or routing error.

Take the thread at the needle end of the path.
Take the thread at the needle end of the path.
Draw the thread gently in front of the machine to feel whether it feeds evenly.
Draw the thread gently in front of the machine to feel whether it feeds evenly.

8. Check under the spool cap

Watch at 02:40

At the thread stand, lift the cone and inspect the cap or holder beneath it. Free any thread caught around or under it. Put the cone back on its stand and guide the strand upward to its own guide before continuing along the same path.

Lifting the green cone exposes the black holder. The video enlarges the area where thread can catch.
Lifting the green cone exposes the black holder. The video enlarges the area where thread can catch.
Check for thread trapped around or underneath the holder before putting the cone back.
Check for thread trapped around or underneath the holder before putting the cone back.
Set the cone back in place and lift the thread into the upward path.
Set the cone back in place and lift the thread into the upward path.

9. Trace the thread through the overhead guide

Watch at 02:52

Follow the same strand up from the cone to its hole in the white guide rail above the spool rack. Trace the matching clear guide tube across to the top of the machine head. Check that the strand can feed freely at the entry and along that path.

The hand points out the guide rail above the thread cones.
The hand points out the guide rail above the thread cones.
Follow the matching clear tube toward the front tension panel.
Follow the matching clear tube toward the front tension panel.

10. Seat the thread in the top tension discs

Watch at 02:59

On the front thread panel, find the small tension knob for this strand in the very top row, just below the clear tube outlet. Check that the thread sits between the tension discs behind the knob. If a small adjustment is needed after the thread is seated, turn the knob clockwise to tighten or counterclockwise to loosen. Pull the thread again to check the change.

The arrow identifies the top-row tension setting immediately under the guide tubes.
The arrow identifies the top-row tension setting immediately under the guide tubes.
The presenter turns the small top-row knob. The dotted wheels are in the row below it.
The presenter turns the small top-row knob. The dotted wheels are in the row below it.

11. Check the wheel and its thread wrap

Watch at 03:18

Trace the strand past its small dotted detector wheel to the matching large grooved wheel in the staggered rows below. At the large wheel, the video calls for one full turn plus half a turn. Use the wheel for your needle, keeping the thread seated in its groove.

The white-dotted detector wheel is above the two staggered rows of large wheels.
The white-dotted detector wheel is above the two staggered rows of large wheels.
The finger moves to the rim of the large wheel to identify the wrap location.
The finger moves to the rim of the large wheel to identify the wrap location.

12. Follow every guide down to the needle

Watch at 03:28

Continue down the same needle's path. Check the small spring guides under the large wheels, the take-up lever in the black slotted panel and the remaining guides down to the needle eye. Rethread any opening the thread has missed and free any trapped segment along the route.

The presenter points to the small guides just below the large wheels.
The presenter points to the small guides just below the large wheels.
Check the hole at the end of the matching take-up lever as the thread continues toward the needle.
Check the hole at the end of the matching take-up lever as the thread continues toward the needle.

13. Pull again to confirm smooth feed

Watch at 03:37

Return to the needle and draw the upper thread gently by hand again. Look for a continuous, even feed as it passes through the guides. If the thread still catches, follow that strand back to the point of resistance before resuming.

Pull again from the same end of the thread path used for the first check.
Pull again from the same end of the thread path used for the first check.
Watch the thread pay out freely in front of the needle head.
Watch the thread pay out freely in front of the needle head.

14. Check the first stitches after restarting

Watch at 03:49

Once the bobbin case and needle are secure and the thread feeds smoothly, clear your hands from the needle and hoop area before resuming. Watch a short run of stitches and check that the repaired thread keeps feeding without another break. The video shows a brief stitch-out on the hooped fabric.

The needle is working over the small green stitches on the hooped fabric.
The needle is working over the small green stitches on the hooped fabric.