SEWTECHSupport Center 简体中文

Import Frame Parameters Only on the ST-1501

Applies to ST-1501

Watch on YouTube ↗

Overview

This ST-1501 procedure imports the Frame settings from a machine-specific parameter file. Have SEWTECH technical support or an authorized technician confirm the file and guide the import. An incorrect file or selection can cause machine errors. Check that Frame is the only selected option before starting and wait for the controller to confirm success before removing the USB drive.

Step-by-step guide

1. Prepare the approved file and insert the USB drive

Watch at 00:11

Under SEWTECH technical support or an authorized technician’s guidance, confirm the parameter file is for your exact ST-1501 and machine configuration. Put only that file on the USB drive. Insert the drive into the port on the right edge of the touchscreen and leave it connected until the import finishes.

The USB drive lines up with the port on the right edge of the touchscreen.
The USB drive lines up with the port on the right edge of the touchscreen.
The drive is seated and the main screen is still visible.
The drive is seated and the main screen is still visible.

2. Open Other Functions

Watch at 00:25

On the main screen, tap the gear at the far right of the bottom blue toolbar. The Other Functions grid opens.

The arrow points to the gear at the right end of the bottom blue toolbar.
The arrow points to the gear at the right end of the bottom blue toolbar.
The Other Functions grid shows Debug at the left of the second row.
The Other Functions grid shows Debug at the left of the second row.

3. Open Debug with technical support

Watch at 00:29

Tap Debug, the wrench-and-screwdriver tile at the left of the second row. In the Number Pad window, enter the Debug password confirmed by your technician, then tap the blue check mark to open the service menu.

Debug is the tool icon in the left column, directly below User Set.
Debug is the tool icon in the left column, directly below User Set.
Enter the password on the digital keypad, then use the blue check mark.
Enter the password on the digital keypad, then use the blue check mark.

4. Open Param(+driver) Import/Export

Watch at 00:39

On page 1/2 of the Debug menu, tap row 9, Param(+driver) Import/Export. It is near the bottom of the list, just above Reset Param.

The highlighted ninth row is Param(+driver) Import/Export.
The highlighted ninth row is Param(+driver) Import/Export.
Tap row 9 to open the parameter import and export menu.
Tap row 9 to open the parameter import and export menu.

5. Choose Param Import

Watch at 00:44

Tap Param Import at the top of the submenu. The USB file list opens. Param Export is the separate second item in this menu.

Param Import is the first row, immediately above Param Export.
Param Import is the first row, immediately above Param Export.
The USB file list opens with the selection controls along the bottom.
The USB file list opens with the selection controls along the bottom.

6. Select and confirm the machine’s parameter file

Watch at 00:47

Tap the approved parameter file in the list. The video highlights paramData.dpdv2 as an example. Verify your file with support, then tap the check mark on the lower-right side of the file browser to open the import options.

The video inset identifies the demonstration file while the presenter points to its list entry.
The video inset identifies the demonstration file while the presenter points to its list entry.
Tap the file list’s check mark beside Exit to confirm the file selection.
Tap the file list’s check mark beside Exit to confirm the file selection.

7. Check which import options are selected

Watch at 00:53

The file-list check mark opens a second dialog. In the video it initially shows checks beside More Set, Frame, and Driver Param Load. Stitch Color Setting is already clear. Check this dialog before touching its lower-right check mark, which starts the import.

The first three rows are checked when the import options first appear.
The first three rows are checked when the import options first appear.

8. Leave only Frame checked

Watch at 00:58

Clear More Set and Driver Param Load if they are selected. Leave Stitch Color Setting unchecked. Verify the four rows from top to bottom: empty, checked, empty, empty. Frame is the second row and should carry the single check mark.

The presenter clears the top row, More Set.
The presenter clears the top row, More Set.
More Set is clear while Driver Param Load still has a check.
More Set is clear while Driver Param Load still has a check.
Final check before importing: Frame is the only selected option.
Final check before importing: Frame is the only selected option.

9. Start the import and wait

Watch at 01:07

With only Frame checked, tap the blue check mark at the bottom right of the options dialog. The dialog closes and the parameter submenu is visible again. Leave the drive plugged in and wait for the success message.

The presenter presses the options dialog’s check mark with Frame alone selected.
The presenter presses the options dialog’s check mark with Frame alone selected.
The submenu is visible again. Leave the USB drive connected while waiting.
The submenu is visible again. Leave the USB drive connected while waiting.

10. Verify the import success message

Watch at 01:12

Wait for the Information dialog to display “import param data success”. This is the controller’s confirmation in the video. Tap the door-shaped Exit icon in that dialog to close it. If the message is missing or the controller reports an error, pause and check with the technician before trying again.

The Information dialog reads “import param data success”.
The Information dialog reads “import param data success”.
The upper Exit icon is inside the success dialog and closes the message.
The upper Exit icon is inside the success dialog and closes the message.

11. Return to the main screen and remove the USB drive

Watch at 01:19

After closing the message, use the Exit icon at the lower-right corner of the parameter submenu to return to the main screen. When the normal design thumbnails and bottom toolbar are visible again, unplug the USB drive from the right side of the touchscreen.

Tap the lower-right Exit icon on the parameter submenu.
Tap the lower-right Exit icon on the parameter submenu.
The design thumbnails are visible again on the main screen, with the drive still attached.
The design thumbnails are visible again on the main screen, with the drive still attached.
Unplug the drive after returning to the main screen.
Unplug the drive after returning to the main screen.