SEWTECHSupport Center 简体中文

Oil the ST-1501 Before First Use at Four Lubrication Points

Applies to ST-1501

Watch on YouTube ↗

Overview

Before the first run, lubricate the four points shown on this ST-1501 head: the rotary hook, the round needle-bar holes, the vertical needle-bar slots and the main oiling hole. Use this guide if those points match your machine head.

Step-by-step guide

1. Prepare the oil and switch off the machine

Watch at 00:13

Have embroidery machine oil in a fine-tip bottle, a soft lint brush, a soft cloth and a piece of scrap fabric ready. Switch off the machine before opening the bobbin cover or oiling the needle bars. The later needle change uses the touchscreen, so power is needed briefly to position the head.

The fine-tip bottle lets you place individual drops. The video starts with the machine switched off.
The fine-tip bottle lets you place individual drops. The video starts with the machine switched off.
The hook sits beneath the needle row. The round holes and vertical slots are on different parts of the front of the head.
The hook sits beneath the needle row. The round holes and vertical slots are on different parts of the front of the head.

2. Open the bobbin cover and clean the hook

Watch at 00:36

Open the small cover below the needle plate. Pull the bobbin case out by its latch to expose the rotary hook. Brush loose thread and lint out of the hook area and the inside of the cover before adding oil.

The cover folds down below the circular bobbin case.
The cover folds down below the circular bobbin case.
Pull the bobbin case toward you by its small latch.
Pull the bobbin case toward you by its small latch.
With the case out, brush lint from the exposed hook area.
With the case out, brush lint from the exposed hook area.

3. Add one or two drops to the rotary hook

Watch at 00:47

With the case removed, aim the fine nozzle at the hook point shown in the close-up and apply one or two drops. For a machine used daily, repeat this at the end of each workday.

The white nozzle points into the exposed rotary hook. The overlay gives the amount as one to two drops.
The white nozzle points into the exposed rotary hook. The overlay gives the amount as one to two drops.
The daily interval applies to the rotary hook on a machine used each day.
The daily interval applies to the rotary hook on a machine used each day.

4. Oil the round needle-bar holes

Watch at 01:00

Find the horizontal row of round holes in the silver front plate just above the needles. Place the fine nozzle at each hole in that row and add two drops per hole. The video specifies weekly maintenance for these holes.

The red box identifies the row of round holes above the needle area.
The red box identifies the row of round holes above the needle area.
The inset shows the fine nozzle at one round hole. Repeat the two-drop dose at each hole.
The inset shows the fine nozzle at one round hole. Repeat the two-drop dose at each hole.

5. Oil the vertical needle-bar slots

Watch at 01:13

Find the row of narrow vertical slots in the dark panel above the silver plate. Aim through each slot at the vertical rod visible inside and apply two drops per slot. Repeat weekly as shown.

The red box identifies the vertical slots in the upper panel.
The red box identifies the vertical slots in the upper panel.
The inset shows where the nozzle reaches the vertical rod inside the slot.
The inset shows where the nozzle reaches the vertical rod inside the slot.
Apply two drops at each slot as you move across the row.
Apply two drops at each slot as you move across the row.

6. Power on briefly and select needle 1

Watch at 01:36

Switch the machine on to position the head for access to the felt. Tap the needle-selection icon in the bottom row of the touchscreen, then tap 1 in the number grid. Check that 1 is highlighted and the head has stopped moving. Switch the machine off before reaching behind the needle bars.

Tap the icon indicated by the fingertip in the bottom row to open the needle-number grid.
Tap the icon indicated by the fingertip in the bottom row to open the needle-number grid.
On this controller, 1 is the rightmost number in the upper row.
On this controller, 1 is the rightmost number in the upper row.
The screen highlights 1 after the head shifts sideways and exposes the side behind the needle bars.
The screen highlights 1 after the head shifts sideways and exposes the side behind the needle bars.

7. Check whether the oil felt is dry

Watch at 01:49

Look through the opening behind the needle bars at the felt above the metal rail. The video calls for checking it every two weeks. If the felt is dry, locate the small round main oiling hole in the white side plate near the black knob.

The arrow points to the felt inside the opening behind the head.
The arrow points to the felt inside the opening behind the head.
The video shows a dry fingertip after checking the felt before oiling.
The video shows a dry fingertip after checking the felt before oiling.
The red circle marks the small main oiling hole in the side plate next to the opening.
The red circle marks the small main oiling hole in the side plate next to the opening.

8. Feed the dry felt one drop at a time

Watch at 01:58

Put one drop into the main oiling hole and wait 3–5 seconds for it to soak in. Repeat one drop at a time, waiting between drops. For the dry felt in this demonstration, the video specifies ten drops in total.

Put the first drop into the small side hole indicated by the nozzle.
Put the first drop into the small side hole indicated by the nozzle.
Pause for 3–5 seconds so the drop can soak in.
Pause for 3–5 seconds so the drop can soak in.
Repeat at the same hole, spacing the drops as shown.
Repeat at the same hole, spacing the drops as shown.

9. Confirm the felt has absorbed the oil

Watch at 02:19

Recheck the same felt through the opening. The video shows a light trace of oil on the fingertip after the check, indicating that the felt has taken up oil.

Recheck the felt at the same opening behind the needle bars.
Recheck the felt at the same opening behind the needle bars.
The arrow points to the sheen on the fingertip after the felt has absorbed oil.
The arrow points to the sheen on the fingertip after the felt has absorbed oil.

10. Wipe excess oil and prepare the hook for sewing

Watch at 02:36

With the machine stopped, wipe off excess oil with a soft cloth, including around the hook and bobbin cover shown here. Check that the bobbin case is seated and close the cover before starting the test.

The soft cloth wipes excess oil from the open cover and around the hook.
The soft cloth wipes excess oil from the open cover and around the hook.
The bobbin case is back in place during the final wipe around the edge.
The bobbin case is back in place during the final wipe around the edge.

11. Run a test on scrap fabric

Watch at 02:46

Hoop a piece of scrap fabric and run the machine on it for about two minutes, as directed in the video. This gives any excess oil a chance to transfer to the scrap. Stop before checking the cloth.

The green scrap fabric is already hooped under the needles.
The green scrap fabric is already hooped under the needles.
The needle is sewing into the scrap during the test.
The needle is sewing into the scrap during the test.

12. Check for oil marks before sewing your project

Watch at 03:00

Check around the test stitching for an oily patch like the one shown. If a mark appears, keep testing on spare fabric and check again. Start using your project fabric only when a fresh test area shows no new oil marks.

The dark patch beside the first test stitches is the oil mark shown in the demo.
The dark patch beside the first test stitches is the oil mark shown in the demo.
The machine continues sewing on the scrap after an oil mark appears.
The machine continues sewing on the scrap after an oil mark appears.