SEWTECHSupport Center 简体中文

Fix Errors 19 and 12 on the ST-1201 and SC-1501

Applies to ST-1201 / SC-1501 Demonstrated on ST-1201

Watch on YouTube ↗

Overview

With embroidery stopped, check the needle number at the upper right of the touchscreen and the circular 100° indicator in the top status bar. Error 19 means the controller has lost the needle position. Error 12 means the main shaft is out of its 100° stop position. The video shows the ST-1201 controls. Have a hex key ready if the shaft needs manual adjustment, and switch the machine off before using it.

Step-by-step guide

1. Error 19 · Check the needle number

Watch at 00:20

Look beside the needle symbol at the upper right of the screen. If the number flickers or reads 0, tap the 100° return button at the far left of the bottom toolbar, beside the scissors. If the Error 19 dialog appears, use the needle-position reset in the next step.

The finger is on the far-left 100° return button in the blue toolbar.
The finger is on the far-left 100° return button in the blue toolbar.
The Error 19 dialog reports an abnormal needle position. The current needle reads 0 at the upper right.
The Error 19 dialog reports an abnormal needle position. The current needle reads 0 at the upper right.

2. Error 19 · Reset the needle on screen

Watch at 00:35

Once the alert is closed, tap the three-needle icon in the bottom toolbar to open the numbered needle panel. Tap the right-hand button of the two small pale buttons at the lower left of the panel. Its icon shows an arrow pointing toward a needle. Repeat if the first tap leaves the reading at 0. A stable nonzero number confirms the reset. The video shows needle 5.

The three-needle icon sits between the scissors and gear icons.
The three-needle icon sits between the scissors and gear icons.
The finger taps the right-hand button of the two pale buttons below the needle numbers.
The finger taps the right-hand button of the two pale buttons below the needle numbers.
The close-up shows a needle reading of 5, also highlighted on the needle panel.
The close-up shows a needle reading of 5, also highlighted on the needle panel.

3. Error 19 · Try the color-change knob

Watch at 00:55

As an alternative, gently turn the black color-change knob a little in each direction while watching the needle reading. On the machine shown, the knob is to the left of the touchscreen beside the thread stand. Stop as soon as a nonzero needle number appears.

The hand turns the black knob beside the thread spools.
The hand turns the black knob beside the thread spools.
The magnified needle reading shows 5 after the knob adjustment.
The magnified needle reading shows 5 after the knob adjustment.

4. Error 12 · Identify the slashed 100° indicator

Watch at 01:16

Look for a slash through the circular 100° indicator in the top status bar. The Error 12 dialog reports that the main shaft did not stop in position. Close the dialog to reach the 100° return button.

The inset shows the slash over the top-bar 100° indicator while the screen displays Error 12.
The inset shows the slash over the top-bar 100° indicator while the screen displays Error 12.

5. Error 12 · Return the shaft to 100° on screen

Watch at 01:34

Tap the 100° return button at the far left of the bottom toolbar. Wait while the machine adjusts. Look back at the circular 100° indicator in the top bar. The slash disappears when the return is complete.

The fingertip marks the bottom-left 100° return button.
The fingertip marks the bottom-left 100° return button.
The top-bar indicator now shows 100° without a slash.
The top-bar indicator now shows 100° without a slash.

6. Error 12 · Switch off for manual adjustment

Watch at 01:53

For the manual method, switch the machine off and wait for the touchscreen to go dark. Have a fitting hex key ready. On the main-shaft access panel, find the small tool opening on the left and the round angle window immediately to its right.

The machine is switched off before the hex key is used.
The machine is switched off before the hex key is used.
The hex socket is visible through the smaller left opening. The angle scale is in the larger right window.
The hex socket is visible through the smaller left opening. The angle scale is in the larger right window.

7. Error 12 · Align the 100° mark and restart

Watch at 02:08

With the machine off, insert the hex key into the small left opening. Turn it slowly while watching the scale in the right window, then stop at the red 100° mark. Remove the key, switch the machine back on, and check that the slash has cleared from the top-bar 100° indicator.

The hex key is in the left opening while the red 100° mark is visible in the right window.
The hex key is in the left opening while the red 100° mark is visible in the right window.
After restart, the 100° indicator is clear of the slash.
After restart, the 100° indicator is clear of the slash.

8. Both errors · Check the screen and take-up lever

Watch at 02:39

The video shows a needle reading of 0, a slash through the top-bar 100° indicator, and a lowered take-up lever at the front of the machine head. Use either of the two sequences below, each in the order shown.

The inset shows both the slashed shaft indicator and the zero needle reading.
The inset shows both the slashed shaft indicator and the zero needle reading.
The presenter points out the lowered take-up lever at the front of the head.
The presenter points out the lowered take-up lever at the front of the head.

9. Both errors · Method 1, recover the needle reading

Watch at 03:01

Gently rock the black color-change knob while watching the needle number. Stop when a nonzero number appears. While the shaft is away from 100°, this recovers the reading for the current needle. In the video, the reading returns to 4 because needle 4 is already in position.

The knob is still in view as the magnified readout shows that needle 4 has been detected.
The knob is still in view as the magnified readout shows that needle 4 has been detected.

10. Both errors · Method 1, then return the shaft

Watch at 03:40

Once the needle number is back, tap the bottom-left 100° return button and let the machine finish. Check that the slash is gone and that the take-up lever has returned to its normal position.

The machine displays a wait message as it returns the shaft to 100°.
The machine displays a wait message as it returns the shaft to 100°.
The presenter checks the take-up lever at the front of the machine head.
The presenter checks the take-up lever at the front of the machine head.

11. Both errors · Method 2, first set the shaft by hand

Watch at 04:03

Switch the power off. With the screen dark, use the hex key in the small left opening and turn slowly until the scale in the right window reaches 100°. Remove the key before switching the machine on. Check the 100° indicator for a clear circle, then check the needle reading separately.

The inset identifies the red power switch. The touchscreen goes dark before the shaft is turned.
The inset identifies the red power switch. The touchscreen goes dark before the shaft is turned.
The inset shows the hex key in the small opening next to the angle window.
The inset shows the hex key in the small opening next to the angle window.
The slash has cleared after restart. Check the needle number before calling the reset complete.
The slash has cleared after restart. Check the needle number before calling the reset complete.

12. Both errors · Method 2, finish the needle reset

Watch at 04:39

If the needle still reads 0, open the needle panel via the three-needle icon. Tap the right-hand button of the two pale buttons at the lower left of the panel. Tap again if the first attempt leaves the reading at 0. The video finishes with a stable needle number, a clear 100° indicator, and the take-up lever back in its normal position.

The finger presses the needle-position reset button. The display still reads 0 at this point.
The finger presses the needle-position reset button. The display still reads 0 at this point.
The inset shows a recovered needle reading of 5.
The inset shows a recovered needle reading of 5.
Check that the take-up lever has returned to its normal position.
Check that the take-up lever has returned to its normal position.