Set the 8-in-1 Hoop Center on the ST-1501
Before you begin
Have one piece of stabilizer for each hoop, a ruler and a washable fabric pen. The video shows the 7 × 5 and R6 from the 8-in-1 magnetic set on an ST-1501. The rectangular and round profiles each store their own center. After saving a center, switch profiles and return to it to check that the laser lands on the marked intersection.
Hoop center setup
1. Clamp the stabilizer in the 7 × 5 hoop
Watch at 00:19 ↗Lay a piece of stabilizer over the lower frame and seat the magnetic top frame over it. Keep your fingers away from the closing edges. Check that the stabilizer is held flat and secure before drawing.
2. Draw the 7 × 5 center crosshair
Watch at 00:28 ↗Use the molded marks on opposite sides of the frame as guides. With a ruler and washable fabric pen, draw a vertical line through the top and bottom marks and a horizontal line through the side marks. The intersection on the stabilizer is the physical center.
3. Seat the hoop in the adapter
Watch at 00:51 ↗Loosen the black knob at the middle of the adapter. Align the hoop’s three mounting openings with the matching slots, then seat the middle opening fully against the top of its slot. Tighten the knob and check that the seated center has no gap and the hoop does not rock.
4. Check the needle-plate reference
Watch at 01:19 ↗Before installing the hoop, look under the needle head and check that the laser dot is centered on the needle-plate hole. The video uses an already aligned laser as the reference for the rest of the setup.
5. Fit the hoop arms and select needle 1
Watch at 01:30 ↗Fit the adapter assembly onto the machine and secure both hoop arms. Check both sides for play. On the touchscreen, tap the three-needle icon on the bottom toolbar and choose 1 on the numbered needle panel before setting the hoop position.
6. Select the installed 7 × 5 profile
Watch at 01:51 ↗Open the hoop selection screen using the wide hoop control just below the frame preview. Find the MG-7×5 card (150 × 95 on the filmed controller) and select it for the installed rectangular hoop. After the frame moves, compare the laser with the crosshair. The video shows an offset before correction.
7. Move the 7 × 5 hoop to the laser
Watch at 02:17 ↗Tap the highlighted frame-parameter button in the left-hand control grid. Use the directional pad at the lower right of the parameter screen to move the carriage until the laser lands on the marked intersection. Keep the signed X and Y movement readings for the next step.
8. Find the two readings for each axis
Watch at 02:33 ↗In Center for compensation, read the signed movement offsets above the white X and Y fields. The white fields hold the saved values you will edit. Add the movement reading to the saved value on the same axis. Keep the plus or minus sign, and calculate from your own screen.
9. Enter the 7 × 5 example values
Watch at 02:59 ↗In the video, the X movement is +1 and the saved X is 156 (156 + 1 = 157). The Y movement is −25 and the saved Y is −58 (−58 + (−25) = −83). Tap the white X field and enter its result on the keypad, then do the same for Y. These are the video’s readings.
10. Confirm and allow the frame to move
Watch at 03:27 ↗Accept the keypad entries, then tap the check mark at the bottom of the frame-parameter screen. A warning can appear before the frame moves. In the 7 × 5 demonstration, the warning mentions the cap frame. Check the travel area is clear, then acknowledge the prompt and wait for the hoop to settle.
11. Reselect 7 × 5 and verify the center
Watch at 03:41 ↗Open the hoop list and select another profile while leaving the mounted 7 × 5 hoop in place for the test. Then go back to the list, reselect 7 × 5 and let the carriage stop. The saved center passes the check when the laser returns to the crosshair without using the direction keys again.
12. Mark the physical center of the R6 hoop
Watch at 04:07 ↗Clamp a fresh piece of stabilizer in R6. Use the top and bottom marks and the matching marks on the two sides to place the vertical and horizontal lines with a ruler. Use their intersection as the laser target for this hoop.
13. Mount R6 and choose its own profile
Watch at 04:38 ↗Fit R6 to the machine and confirm both adapter arms are secure. Tap the hoop control to open the list and choose the R6 card. The controller shows a circular frame outline. Wait for movement to stop and inspect the laser against the R6 crosshair before correcting it.
14. Align R6 with the arrow keys
Watch at 05:01 ↗Open the same frame-parameter page and use its lower-right arrow pad to move R6 until the laser is directly over the crossed lines. Read the X and Y movement values from this alignment. R6 has its own saved values and offsets.
15. Enter and confirm the R6 values
Watch at 05:15 ↗In the video, the R6 X movement is +2 and its saved X is 156, so 156 + 2 = 158. The Y movement is −28 and its saved Y is −67, so −67 + (−28) = −95. Enter your corresponding results through the white X and Y fields. Use the keypad check mark to accept each entry.
16. Save the R6 center
Watch at 05:46 ↗Tap the check mark at the bottom of the frame-parameter screen. When the movement warning appears, check the travel area and acknowledge it. Wait for the circular frame view to return and the hoop to settle.
17. Reselect R6 and check its laser return
Watch at 05:58 ↗Select another profile from the hoop list, then select R6 again with R6 still mounted. Wait for the frame to stop. The circular profile returns on screen, and the laser should land on the marked intersection. Repeat the alignment check if the dot still sits beside the crosshair.