SEWTECHSupport Center 简体中文

Floral Sneaker Embroidery with the SEWTECH Shoe Clamp

Applies to ST-1501

Watch on YouTube ↗

Overview

This SEWTECH ST-1501 demonstration pairs the blue SEWTECH Shoe Clamp with a white high-top canvas sneaker and a floral design digitized by GOCA Embroidery. Watch how the shoe is held at the outer ankle panel, where the operator starts the machine, and what the screen and the finished stitching look like.

Video highlights

1. Locate the area to embroider

Watch at 00:02

The operator points to the blank outer ankle panel of the high-top sneaker. This is the surface that needs to lie flat in the clamp. The finished motif fits between the eyelets and the back of the shoe.

The fingertip marks the blank canvas between the eyelets and the rear edge of the upper.
The fingertip marks the blank canvas between the eyelets and the rear edge of the upper.

2. Fasten the clamp to the carriage

Watch at 00:03

The blue mounting bar sits below the ruler on the machine. Watch the operator use an L-shaped hex key on the two mounting screws, one on either side. From the front, the two blue fingers project below the needle row.

The hex key engages one mounting screw beside the black knob on the blue bar.
The hex key engages one mounting screw beside the black knob on the blue bar.
The second mounting screw is shown from the other side of the machine.
The second mounting screw is shown from the other side of the machine.

3. Secure the shoe and flatten the side panel

Watch at 00:08

Support the sole and guide the empty shoe opening onto the mounted clamp from the front. The operator reaches beside the head to work the clamp lever while holding the shoe. Before stitching, the white canvas lies flat between the blue fingers and the sole hangs clear below. The shoe should stay fixed relative to the clamp as the carriage moves.

The shoe comes in from the front with the sole supported by hand.
The shoe comes in from the front with the sole supported by hand.
The operator works the small clamp lever beside the head.
The operator works the small clamp lever beside the head.
The two blue fingers hold the canvas flat around the exposed stitch area.
The two blue fingers hold the canvas flat around the exposed stitch area.

4. Check the floral preview and start

Watch at 00:12

The ST-1501 screen shows the floral design already loaded. The operator presses the round blue-ringed physical Start button below the screen. The clip cuts from this press to the first stitches.

The floral preview is on screen as the operator presses the blue-ringed button below it.
The floral preview is on screen as the operator presses the blue-ringed button below it.

5. Watch the floral stitches build up

Watch at 00:13

The first close-ups show red stitches on the exposed canvas. Later shots show the colored fills and dark outlines taking shape between the same two clamp fingers. The montage skips through the stitching in several cuts.

Early red stitches are visible between the two blue fingers.
Early red stitches are visible between the two blue fingers.
Pink petals, green leaves and dark outlines are visible as the needle works.
Pink petals, green leaves and dark outlines are visible as the needle works.

6. Read the completion message

Watch at 00:28

At the end of the run, the controller displays “Embroidery completed!” over the colored floral preview. In the following shot, the shoe is still held under the head before the operator takes it out.

The controller displays “Embroidery completed!” over the floral design.
The controller displays “Embroidery completed!” over the floral design.

7. Remove the shoe and inspect the motif

Watch at 00:29

After the machine stops, the operator supports the sole and takes the shoe out toward the front. In the final close-up, the pink flowers, green leaves and dark outlines sit on the outer ankle panel between the eyelets and the heel.

The operator supports the shoe from below before taking it clear of the clamp.
The operator supports the shoe from below before taking it clear of the clamp.
The finished flower motif is shown on the outer side of the sneaker.
The finished flower motif is shown on the outer side of the sneaker.