SEWTECHSupport Center 简体中文

Set the 8-in-1 Hoop Center on the ST-1501

Machine ST-1501 8-in-1 magnetic hoop set

Watch on YouTube ↗

Before you begin

Have one piece of stabilizer for each hoop, a ruler and a washable fabric pen. The video shows the 7 × 5 and R6 from the 8-in-1 magnetic set on an ST-1501. The rectangular and round profiles each store their own center. After saving a center, switch profiles and return to it to check that the laser lands on the marked intersection.

Hoop center setup

1. Clamp the stabilizer in the 7 × 5 hoop

Watch at 00:19 ↗

Lay a piece of stabilizer over the lower frame and seat the magnetic top frame over it. Keep your fingers away from the closing edges. Check that the stabilizer is held flat and secure before drawing.

The top frame goes over the stabilizer. Keep fingers clear as it closes.
The top frame goes over the stabilizer. Keep fingers clear as it closes.
The stabilizer is held between the two frames.
The stabilizer is held between the two frames.

2. Draw the 7 × 5 center crosshair

Watch at 00:28 ↗

Use the molded marks on opposite sides of the frame as guides. With a ruler and washable fabric pen, draw a vertical line through the top and bottom marks and a horizontal line through the side marks. The intersection on the stabilizer is the physical center.

Use the molded mark at the edge to place the centerline.
Use the molded mark at the edge to place the centerline.
Use a ruler to draw the horizontal line across the vertical one.
Use a ruler to draw the horizontal line across the vertical one.
The finger points to the two lines’ intersection.
The finger points to the two lines’ intersection.

3. Seat the hoop in the adapter

Watch at 00:51 ↗

Loosen the black knob at the middle of the adapter. Align the hoop’s three mounting openings with the matching slots, then seat the middle opening fully against the top of its slot. Tighten the knob and check that the seated center has no gap and the hoop does not rock.

Loosen the black knob at the center of the adapter.
Loosen the black knob at the center of the adapter.
The red box shows the three mounting openings and their matching slots.
The red box shows the three mounting openings and their matching slots.
Check the center mounting point for a gap after tightening.
Check the center mounting point for a gap after tightening.

4. Check the needle-plate reference

Watch at 01:19 ↗

Before installing the hoop, look under the needle head and check that the laser dot is centered on the needle-plate hole. The video uses an already aligned laser as the reference for the rest of the setup.

The red circle identifies the needle-plate reference under the head.
The red circle identifies the needle-plate reference under the head.
Check the hole indicated at the needle plate before mounting the hoop.
Check the hole indicated at the needle plate before mounting the hoop.

5. Fit the hoop arms and select needle 1

Watch at 01:30 ↗

Fit the adapter assembly onto the machine and secure both hoop arms. Check both sides for play. On the touchscreen, tap the three-needle icon on the bottom toolbar and choose 1 on the numbered needle panel before setting the hoop position.

The red arrows mark the two machine-side mounting points.
The red arrows mark the two machine-side mounting points.
The three-needle icon opens the needle selector.
The three-needle icon opens the needle selector.
Choose 1 at the right end of the top numbered row.
Choose 1 at the right end of the top numbered row.

6. Select the installed 7 × 5 profile

Watch at 01:51 ↗

Open the hoop selection screen using the wide hoop control just below the frame preview. Find the MG-7×5 card (150 × 95 on the filmed controller) and select it for the installed rectangular hoop. After the frame moves, compare the laser with the crosshair. The video shows an offset before correction.

The wide hoop control directly below the outline opens the hoop list.
The wide hoop control directly below the outline opens the hoop list.
The 7 × 5 profile is the rectangular card highlighted in the second row.
The 7 × 5 profile is the rectangular card highlighted in the second row.
The selection can display a movement warning before the rectangular outline appears.
The selection can display a movement warning before the rectangular outline appears.
Before the correction, the crosshair and the laser position do not coincide.
Before the correction, the crosshair and the laser position do not coincide.

7. Move the 7 × 5 hoop to the laser

Watch at 02:17 ↗

Tap the highlighted frame-parameter button in the left-hand control grid. Use the directional pad at the lower right of the parameter screen to move the carriage until the laser lands on the marked intersection. Keep the signed X and Y movement readings for the next step.

The arrow points to the frame-parameter button in the left-hand control grid.
The arrow points to the frame-parameter button in the left-hand control grid.
The right-hand arrow pad moves the hoop. The inset shows the crosshair under the laser.
The right-hand arrow pad moves the hoop. The inset shows the crosshair under the laser.

8. Find the two readings for each axis

Watch at 02:33 ↗

In Center for compensation, read the signed movement offsets above the white X and Y fields. The white fields hold the saved values you will edit. Add the movement reading to the saved value on the same axis. Keep the plus or minus sign, and calculate from your own screen.

The red box highlights the offset display and the stored X/Y fields beneath it.
The red box highlights the offset display and the stored X/Y fields beneath it.
The video’s enlarged inset shows the signed movement and the editable fields as separate rows.
The video’s enlarged inset shows the signed movement and the editable fields as separate rows.

9. Enter the 7 × 5 example values

Watch at 02:59 ↗

In the video, the X movement is +1 and the saved X is 156 (156 + 1 = 157). The Y movement is −25 and the saved Y is −58 (−58 + (−25) = −83). Tap the white X field and enter its result on the keypad, then do the same for Y. These are the video’s readings.

7 × 5 X example. 156 + 1 = 157. The enlarged inset shows the keypad.
7 × 5 X example. 156 + 1 = 157. The enlarged inset shows the keypad.
7 × 5 Y example. −58 + (−25) = −83.
7 × 5 Y example. −58 + (−25) = −83.
Use the keypad to enter the signed Y result.
Use the keypad to enter the signed Y result.

10. Confirm and allow the frame to move

Watch at 03:27 ↗

Accept the keypad entries, then tap the check mark at the bottom of the frame-parameter screen. A warning can appear before the frame moves. In the 7 × 5 demonstration, the warning mentions the cap frame. Check the travel area is clear, then acknowledge the prompt and wait for the hoop to settle.

Acknowledge the movement warning with the check mark on the dialog.
Acknowledge the movement warning with the check mark on the dialog.
The screen returns to the rectangular frame view after confirmation.
The screen returns to the rectangular frame view after confirmation.

11. Reselect 7 × 5 and verify the center

Watch at 03:41 ↗

Open the hoop list and select another profile while leaving the mounted 7 × 5 hoop in place for the test. Then go back to the list, reselect 7 × 5 and let the carriage stop. The saved center passes the check when the laser returns to the crosshair without using the direction keys again.

Open the hoop list and switch to a different profile for the test.
Open the hoop list and switch to a different profile for the test.
After reselecting 7 × 5, the frame stops in the position used for the crosshair check.
After reselecting 7 × 5, the frame stops in the position used for the crosshair check.

12. Mark the physical center of the R6 hoop

Watch at 04:07 ↗

Clamp a fresh piece of stabilizer in R6. Use the top and bottom marks and the matching marks on the two sides to place the vertical and horizontal lines with a ruler. Use their intersection as the laser target for this hoop.

The presenter points out the center mark at the top of the R6 hoop.
The presenter points out the center mark at the top of the R6 hoop.
The side marks guide placement of the horizontal centerline.
The side marks guide placement of the horizontal centerline.
The point inside the circle is the R6 crosshair intersection.
The point inside the circle is the R6 crosshair intersection.

13. Mount R6 and choose its own profile

Watch at 04:38 ↗

Fit R6 to the machine and confirm both adapter arms are secure. Tap the hoop control to open the list and choose the R6 card. The controller shows a circular frame outline. Wait for movement to stop and inspect the laser against the R6 crosshair before correcting it.

Seat the assembly at both machine-side mounting points.
Seat the assembly at both machine-side mounting points.
Choose the round R6 card on the right of the hoop list.
Choose the round R6 card on the right of the hoop list.
The circled area shows the crosshair before R6 is corrected.
The circled area shows the crosshair before R6 is corrected.

14. Align R6 with the arrow keys

Watch at 05:01 ↗

Open the same frame-parameter page and use its lower-right arrow pad to move R6 until the laser is directly over the crossed lines. Read the X and Y movement values from this alignment. R6 has its own saved values and offsets.

The red box marks the arrow pad used to move R6.
The red box marks the arrow pad used to move R6.
Use the inset view of the hoop to judge the position while moving it.
Use the inset view of the hoop to judge the position while moving it.

15. Enter and confirm the R6 values

Watch at 05:15 ↗

In the video, the R6 X movement is +2 and its saved X is 156, so 156 + 2 = 158. The Y movement is −28 and its saved Y is −67, so −67 + (−28) = −95. Enter your corresponding results through the white X and Y fields. Use the keypad check mark to accept each entry.

R6 X example. 156 + 2 = 158. The arrow points to the white X field.
R6 X example. 156 + 2 = 158. The arrow points to the white X field.
R6 Y example. −67 + (−28) = −95. The arrow highlights the Y entry area.
R6 Y example. −67 + (−28) = −95. The arrow highlights the Y entry area.
The keypad shows −95 and the check mark used to accept it.
The keypad shows −95 and the check mark used to accept it.

16. Save the R6 center

Watch at 05:46 ↗

Tap the check mark at the bottom of the frame-parameter screen. When the movement warning appears, check the travel area and acknowledge it. Wait for the circular frame view to return and the hoop to settle.

After the keypad closes, use the check mark at the bottom of the parameter screen.
After the keypad closes, use the check mark at the bottom of the parameter screen.
The controller displays a movement warning before returning to the frame view.
The controller displays a movement warning before returning to the frame view.
The controller returns to the round R6 frame view.
The controller returns to the round R6 frame view.

17. Reselect R6 and check its laser return

Watch at 05:58 ↗

Select another profile from the hoop list, then select R6 again with R6 still mounted. Wait for the frame to stop. The circular profile returns on screen, and the laser should land on the marked intersection. Repeat the alignment check if the dot still sits beside the crosshair.

A different, narrow rectangular profile is shown during the switch-away test.
A different, narrow rectangular profile is shown during the switch-away test.
The arrow identifies the R6 card to reselect after the switch-away test.
The arrow identifies the R6 card to reselect after the switch-away test.
The circular R6 outline returns after R6 is selected again.
The circular R6 outline returns after R6 is selected again.
The final close-up shows where to verify the crosshair under the laser.
The final close-up shows where to verify the crosshair under the laser.
This guide is based on the original SEWTECH TV footage and YouTube’s automatic English captions. Image timestamps mark the frames shown. Each step’s video link starts at the beginning of that segment.