SEWTECHSupport Center 简体中文

Check and Adjust Bobbin Tension on the ST-1201

Applies to ST-1201

Watch on YouTube ↗

Overview

Use this bench test to check the ST-1201 bobbin tension. Have the bobbin and its case out of the machine, and keep a small flat-blade screwdriver handy. The check is based on how the suspended case moves when you hold the thread.

The original video cover is labeled ST-1501. This guide applies to the ST-1201.

Step-by-step guide

1. Seat the bobbin in its case

Watch at 00:06

Hold the case with the open side facing you. Set the bobbin into the round opening and press it into place with your thumb. Keep the thread tail accessible at the edge of the case.

The open bobbin case and the separate bobbin before assembly.
The open bobbin case and the separate bobbin before assembly.
The thumb seats the bobbin in the opening while keeping the thread tail accessible.
The thumb seats the bobbin in the opening while keeping the thread tail accessible.

2. Route the thread through the threading guide

Watch at 00:11

Turn the case so you can see its outer edge. Pull the tail into the slot and through the threading guide on the side. Leave the final wrap around the small wire spring until the tension check is finished.

The fingers bring the thread tail to the edge of the case.
The fingers bring the thread tail to the edge of the case.
The thread comes out at the side after passing through the guide.
The thread comes out at the side after passing through the guide.

3. Suspend the case by the thread

Watch at 00:15

Pinch the free end of the thread and let go of the case. Let it hang clear of the work surface. Keep your other hand underneath to catch it if it falls, with space for the case to move freely during the test.

The fingers hold the thread alone, leaving the case free to move below.
The fingers hold the thread alone, leaving the case free to move below.

4. Limit each adjustment to a small turn

Watch at 00:25

The tension spring responds to very small changes. If the drop test calls for an adjustment, turn the larger screw about 1/10 to 1/8 of a turn at a time. Avoid a half or full turn in one adjustment. Repeat the drop test before deciding whether to turn it again.

The inset points to the adjustment screw and shows the recommended fraction of a turn.
The inset points to the adjustment screw and shows the recommended fraction of a turn.
The video warns against turning the screw by a half or full turn at once.
The video warns against turning the screw by a half or full turn at once.

5. Recognize a loose bobbin

Watch at 00:47

Hold the thread still and watch what happens when the case is unsupported. If the case runs down the thread quickly under its own weight, with almost no resistance and without a wrist flick, the bobbin tension is too loose.

Just before release, one hand pinches the thread and the other still supports the case.
Just before release, one hand pinches the thread and the other still supports the case.
The case has dropped into the open palm under its own weight.
The case has dropped into the open palm under its own weight.

6. Tighten a loose bobbin case

Watch at 00:58

Support the case in one hand. Seat the small flat-blade screwdriver in the larger screw nearest the thread exit and turn it clockwise by about 1/10 to 1/8 turn. Hang the case by the thread again to check whether it still drops by itself.

The screwdriver turns the larger screw clockwise to increase tension.
The screwdriver turns the larger screw clockwise to increase tension.
The presenter grips the thread above the case to repeat the drop test.
The presenter grips the thread above the case to repeat the drop test.

7. Identify the two screws on the case

Watch at 01:23

Find the larger screw next to the thread exit on the outside of the case. This is the tension adjustment screw in both directions. Leave the adjacent smaller screw in place during normal tension adjustment. It holds the tension spring in place.

The large slotted screw closest to the thread exit adjusts the tension.
The large slotted screw closest to the thread exit adjusts the tension.
The smaller screw above it in this close-up holds the tension spring.
The smaller screw above it in this close-up holds the tension spring.

8. Recognize an overtight bobbin

Watch at 01:43

Suspend the case by the thread and give your wrist a firm shake. If the case stays at essentially the same point on the thread or moves down very slowly, the tension is too tight.

The case is suspended above the open palm before the firmer movement.
The case is suspended above the open palm before the firmer movement.
After the firm shake, the case still hangs above the hand with little thread released.
After the firm shake, the case still hangs above the hand with little thread released.

9. Loosen an overtight bobbin case

Watch at 01:54

Turn the same larger screw counterclockwise by about 1/10 to 1/8 turn, then repeat the drop test. The video overlay near 01:58 calls this tightening. Follow the narration here. A counterclockwise turn loosens the tension.

Screwdriver placement for the counterclockwise adjustment on the larger screw.
Screwdriver placement for the counterclockwise adjustment on the larger screw.
The case is suspended by the thread again after a small adjustment.
The case is suspended by the thread again after a small adjustment.
If another correction is needed, make one more small turn and check again.
If another correction is needed, make one more small turn and check again.

10. Confirm the case slides briefly and stops

Watch at 02:24

First check that the freely hanging case stays still. Give your wrist one gentle flick. The target described in the video is a smooth drop of about 3–5 cm (roughly 1–2 in), followed by a stop on its own. Keep your catching hand low enough to see whether the case stops before it reaches your palm. The video catches the case in an open palm, so use the narrated drop-and-stop test when judging your own result.

The case hangs from the thread at rest before the wrist flick.
The case hangs from the thread at rest before the wrist flick.
A gentle wrist flick lets the case slide down the thread.
A gentle wrist flick lets the case slide down the thread.

11. Finish by routing the thread around the wire spring

Watch at 02:45

Once the tension is set, turn the case sideways to expose the small wire spring. Guide the loose thread around the spring as shown and pull it lightly upward. Check that the thread follows the path shown in the magnified view.

The presenter points to the small wire spring before routing the thread.
The presenter points to the small wire spring before routing the thread.
The magnified view shows the thread engaged around the small wire spring.
The magnified view shows the thread engaged around the small wire spring.