Set Magnetic Hoop Parameters on the ST-1501
Overview
Measure and mark the physical center of a magnetic hoop, record a stitch area with clearance, and save and test the hoop’s center on the ST-1501. Have the hoop, a piece of stabilizer, a ruler and a washable fabric pen ready.
Step-by-step guide
1. Clamp stabilizer in the magnetic hoop
Watch at 00:10Lay the lower hoop flat on the table and spread a piece of stabilizer over the opening. Seat the magnetic top frame over it. Check that the stabilizer lies flat, is held all the way around and gives you room to mark the center.


2. Measure and mark the physical center
Watch at 00:17Measure the horizontal length and vertical width of the hoop opening with a ruler. Find the midpoint in each direction. With a washable fabric pen, draw a vertical midline and then a horizontal midline on the stabilizer. The intersection is the mark you will align with the laser.




3. Check the laser at the needle plate
Watch at 00:43With the hoop still off the machine, check that the red laser dot falls on the center reference on the needle plate. Get those two points aligned before using the laser to locate the hoop center.


4. Mount the marked hoop securely
Watch at 00:56Slide the hoop onto the machine’s two hoop arms with the marked stabilizer facing up. Seat both side brackets fully. Gently check that both sides are secure and the hoop does not wobble.


5. Select needle 1
Watch at 01:04Tap the three-needle icon on the bottom bar to open the manual needle selector. Tap 1 at the right end of the upper row. Let the head shift to needle 1 before setting the frame position. The 1 button becomes highlighted.



6. Open frame selection and choose None Frame
Watch at 01:12On the touchscreen, open the frame controls using the highlighted fourth tab in the middle row. Tap the current-frame field to bring up the hoop list. At the bottom of the list, select None Frame and tap the blue checkmark. The preview then reports that no frame is selected. The example hoop already appears in the presenter’s machine history, so your existing list may differ.




7. Open frame parameters and add an entry
Watch at 01:32Back on the frame-controls page, tap the left button in the second row of the small control grid below the current-frame field. On the parameter page, tap Add below the dimension fields, beside Delete. The video shows a new slot with blank or zeroed dimensions ready for entry.



8. Enter the safe stitch-area dimensions
Watch at 01:41Use the opening you measured to size the stitch area. The video recommends making each overall dimension 20–25 mm smaller to leave clearance from the frame. In the 200 × 150 mm example, open Frame Length, enter 180, and accept with the keypad checkmark. Do the same for Frame Width with 125. Calculate the entries from your own hoop’s measurements.



9. Set the frame chamfer
Watch at 02:12Tap Frame Chamfer under the width field, enter the value for this hoop’s corners and confirm it on the numeric keypad. The demonstration uses 20 for the example hoop. Before proceeding, check that the panel shows all three intended entries.


10. Send the hoop to the frame origin
Watch at 02:22Tap the frame-origin control in the lower toolbar of the parameter page, third button from the left. When Seek Frame Origin appears, keep the hoop’s travel path clear and tap the dialog checkmark. Watch the carriage move and wait for it to stop at its starting position.



11. Jog the hoop until the laser meets the mark
Watch at 02:30Use the direction arrows on the right of the frame-parameter screen to move the mounted hoop. Watch the red dot against the two pen lines. Stop when the dot sits on their intersection, then read the current X and Y above the offset fields.



12. Save the center offsets and confirm
Watch at 02:47In Center for compensation, read the live X and Y while the dot still sits on the mark. Tap the disk icon to write the live readings into the X and Y fields below. Check that the stored values match the live readings. In the video they are X 178 and Y −79. Tap the parameter page checkmark and then the dialog checkmark after checking the movement path.




13. Reselect the saved hoop
Watch at 02:59Open the hoop list again from the current-frame field. Use the bottom next-page arrow to find the saved size. The example 180 × 125 tile is on page 4/4. Tap it and check that its label turns yellow, then tap the blue checkmark. Confirm the movement warning when the path is clear.




14. Run the center command and verify the laser
Watch at 03:09On the frame-controls screen, tap the center command at the upper left of the small button grid. Confirm the Move design to frame center? prompt and let the hoop come to a stop. Check the stabilizer in the hoop. The red dot should fall on the pen-line intersection again. That alignment is the video’s final check that the saved center works. Before stitching, check that the design fits the configured area and that the frame clears the needle throughout the intended movement.


