Assemble the Stand and Mount the ST-1201 and SC-1501
Overview
Follow the ST-1201 demonstration to assemble the stand for the ST-1201 or SC-1501, fit the machine feet and thread rack, then lift the machine onto the four mounting pads. Have a second person ready for the lift and settle the stand on its four floor supports first.
Step-by-step guide
1. Lay out the parts and tools
Watch at 00:15Set out two main frames, three support plates (one with the SEWTECH logo), one storage shelf, the screws and nuts, four round mounting pads and four leveling casters. Take the L-shaped hex key, open-end wrench and folding hex-key set from the toolbox. Keep the four machine feet ready for the underside of the machine.




2. Set both main frames upside down
Watch at 00:59Set the two frames opposite each other. On each frame, the end plates with four caster holes face upward. At the floor end, turn the tabs with a single hole inward toward the space between the frames.


3. Fasten all four caster assemblies
Watch at 01:12Seat a caster plate on each of the four corners. Swivel the wheel out of the way to reach the holes. Insert the screws from the plate side and start the nuts underneath by hand. Hold each nut with the open-end wrench while tightening the screw with the hex key. Repeat at all four corners and check each plate sits flat on the frame.




4. Start the first cross brace loosely
Watch at 02:22Span the two upside-down frames with the first plain support plate near the caster end. Align the two holes at each end. Start all four screws by hand, then snug them lightly with the tools. Leave enough play between the frames to line up the shelf in the next step.



5. Align and secure the storage shelf
Watch at 02:57Hold the shelf between the frames at the middle mounting holes. If a gap keeps the holes from lining up, nudge the two frames closer together or farther apart. Start the shelf screws by hand at the corners, then tighten them with the hex key. Once the shelf is seated, the video returns to the first brace and tightens it.




6. Fasten the two remaining support plates
Watch at 04:08Keep the stand upside down. Fit the remaining plain plate across one open side and the logo plate across the opposite side. The logo faces outward and appears upside down at this point. Start the two screws at each end, then tighten the plates against the frames with the supplied tools.



7. Turn the completed frame upright
Watch at 05:14With the shelf and plates secured, take one side of the stand each and turn it over together as shown. Set the four casters on the floor. The four single-hole tabs should now be at the top and the SEWTECH logo should read upright.


8. Install the four round mounting pads
Watch at 05:27Fit one pad on each top tab, with the recessed cup facing upward. Pass the supplied flat-head screw down through the center and start the nut below the tab. Hold the nut with the open-end wrench and tighten from above with the hex key. Make sure all four cups sit flat on the tabs.




9. Install the feet under the machine base
Watch at 06:01Before lifting the machine onto the stand, run the nuts down each foot's threaded stem toward the black foot pad to expose the threads. With a helper steadying the machine as shown, thread a foot into each of the four underside mounting points. Check that all four feet are fitted before lifting.



10. Lower the floor supports before mounting the machine
Watch at 06:26Roll the empty stand to the installation spot. Turn the round support foot on each caster assembly down until it rests firmly on the floor and supports the stand. Repeat at all four corners, then check the stand does not rock or roll. If you need to move it later, raise the supports so the casters can roll again. Lower them again at the new location.




11. Find the four thread-rack rod positions
Watch at 07:27Locate the four rod positions around the spool platform. On each metal rod, identify the spacer end and keep it facing down. Remove the screw from that end and keep it for the lower attachment.



12. Fasten the rods from under the spool platform
Watch at 07:46Lift the white thread-guide cover clear of the spools. From below the lower spool platform, pass the screw upward through the mounting hole. Hold it from below while turning the rod onto it from above until the rod is secure. Repeat at the other three positions.



13. Refit the thread-guide cover and tighten it
Watch at 08:25Remove the four screws from the tops of the rods. Lower the cover onto the rods and align its four mounting holes. Reinstall the screws through the cover with the fitting hex key. Start all four before fully tightening them, then check the cover is seated at every rod.




14. Lift from the base and seat all four feet
Watch at 09:38Have two people lift the machine together, one on each side, using the grip points under the base shown in the inset. Lower it slowly so all four machine feet land in their matching round pads. Before letting go, check that each foot is centered and seated flat and that the stand stays still. The video ends with the machine seated on the stand.



