SEWTECHSupport Center 简体中文

Set Up and Use the SEWTECH Bobbin Winder

Tool SEWTECH bobbin winder

Watch on YouTube ↗

Overview

Set up the standalone SEWTECH bobbin winder, guide the thread through the tension assembly, and wind a bobbin until the unit stops automatically. The controls below match the winder shown in the video.

Step-by-step guide

1. Gather the winder and supplies

Watch at 00:06

Set out the SEWTECH bobbin winder, an empty bobbin, a cone of bobbin thread, the metal thread guide stand and a wrench.

The empty metal bobbin sits in front of the thread cone.
The empty metal bobbin sits in front of the thread cone.
The wrench and loose guide stand are to the left of the cone.
The wrench and loose guide stand are to the left of the cone.

2. Plug in the winder

Watch at 00:21

Plug the winder’s power cord into an outlet. Leave the front power switch off while you install the stand and thread the winder.

The cord plugs into the outlet. The red rocker on the front switches the winder on later.
The cord plugs into the outlet. The red rocker on the front switches the winder on later.

3. Loosen the nut and screw in the guide stand

Watch at 00:24

Loosen the nut on the threaded end of the guide stand by hand, leaving the threads exposed. Insert that end into the small mounting hole behind the white tension knob on the top right of the winder. Rotate the stand clockwise to screw it in.

Loosen the nut on the straight threaded end of the stand.
Loosen the nut on the straight threaded end of the stand.
The arrow identifies the threaded mounting hole behind the tension knob.
The arrow identifies the threaded mounting hole behind the tension knob.
Insert the stand and turn it clockwise in the hole.
Insert the stand and turn it clockwise in the hole.

4. Aim the hook and tighten the nut

Watch at 00:41

Turn the stand so its upper hook points outward to the right, toward the side where the thread cone will sit. Hold the stand in that position, run the nut down to the top of the housing and tighten it with the wrench so the stand stays in place.

The upper hook points out past the right side of the machine.
The upper hook points out past the right side of the machine.
The wrench tightens the nut at the base of the guide stand.
The wrench tightens the nut at the base of the guide stand.

5. Feed thread through the upper hook

Watch at 00:59

Set the thread cone upright on the table to the right of the winder, on the hook side. Bring the free end up from the cone, through the loop at the tip of the stand, then down toward the tension assembly.

The cone stands on the table on the same side as the hook.
The cone stands on the table on the same side as the hook.
The inset shows the loop the free end passes through.
The inset shows the loop the free end passes through.

6. Thread the tension guide and disc

Watch at 01:07

Feed the end through the small guide hole at the base of the white tension knob. Slip the thread under the tension disc as shown in the close-up, then draw the free end across toward the spindle.

The small guide hole is at the base of the tension assembly.
The small guide hole is at the base of the tension assembly.
The inset shows the thread seated under the disc beneath the white knob.
The inset shows the thread seated under the disc beneath the white knob.

7. Mount the bobbin and secure the thread

Watch at 01:19

Set the empty bobbin on the upright spindle on the left. Viewed from above, wrap the free end around the bobbin core counterclockwise about seven to eight times to hold it in place. Then push the bobbin down onto the spindle.

Set the bobbin over the upright spindle on the left.
Set the bobbin over the upright spindle on the left.
Hold the thread end and make the starter wraps around the bobbin core.
Hold the thread end and make the starter wraps around the bobbin core.
Press the bobbin down onto the spindle after wrapping the thread.
Press the bobbin down onto the spindle after wrapping the thread.

8. Check the thread and correct loose winding

Watch at 01:34

The thread should build up snugly and evenly on the bobbin. If it winds loosely, turn the white tension knob clockwise to increase the tension and check the winding again.

Turn the white knob clockwise if the bobbin thread is loose.
Turn the white knob clockwise if the bobbin thread is loose.

9. Switch on and start winding

Watch at 01:51

Turn on the front rocker switch. Press the large square red START button on top. The bobbin spins and the green indicator lights while the winder runs.

The red rocker on the front supplies power.
The red rocker on the front supplies power.
Press the large red square START button on top.
Press the large red square START button on top.
The green indicator is lit while the bobbin winds.
The green indicator is lit while the bobbin winds.

10. Pause and resume winding

Watch at 01:57

To pause, press the small round red STOP control on the label next to START. The spindle stops and the green indicator goes out. Press the large square red START button again to resume.

Press the round STOP control on the printed panel.
Press the round STOP control on the printed panel.
After pausing, the green light is off and the red light is still on.
After pausing, the green light is off and the red light is still on.
Press the square START button again to resume.
Press the square START button again to resume.

11. Wait for the automatic stop

Watch at 02:07

The demonstrated winder stops automatically when the bobbin is full. Before lifting the bobbin, check that the spindle has stopped, the green indicator is off and the thread is wound evenly between the bobbin flanges.

The green running light is still on during the last part of winding.
The green running light is still on during the last part of winding.
The full bobbin is stationary and the green light is off.
The full bobbin is stationary and the green light is off.

12. Lift off the bobbin and cut the thread

Watch at 02:12

Lift the stopped bobbin straight off the spindle. Hold the bobbin and draw the connecting thread against the small curved metal cutter in front of the spindle. Check that the thread is cut and the filled bobbin is free.

Grip the two sides of the stationary bobbin to lift it off.
Grip the two sides of the stationary bobbin to lift it off.
Bring the connecting thread against the small curved metal cutter.
Bring the connecting thread against the small curved metal cutter.
The wound bobbin is free of the supply thread.
The wound bobbin is free of the supply thread.