SEWTECHSupport Center 简体中文

Use a Magnetic Sash Frame on the ST-1201 and SC-1501

Applies to ST-1201 / SC-1501 Demonstrated on ST-1201

Watch on YouTube ↗

Overview

Install the flat table, mount the magnetic sash frame, and hold the backing and fabric flat before setting up the design. The video demonstrates the ST-1201 using a cutaway stabilizer and a floral design. Follow the screen preview and trace the design on the fabric before starting.

Step-by-step guide

1. Prepare the table parts and screws

Watch at 00:21

Lay out the tabletop, two support brackets, and toolbox. Set out the screwdriver and sort the hardware into small bracket screws, two long knob screws, and two short knob screws. The knob screws are used when mounting the table to the machine.

The brackets, tabletop, and toolbox are laid out for assembly.
The brackets, tabletop, and toolbox are laid out for assembly.
The on-screen list separates the two short and two long knob screws from the small screws.
The on-screen list separates the two short and two long knob screws from the small screws.

2. Align both support brackets

Watch at 00:47

Match the brackets to the 12 mounting holes in the tabletop. Fit the black brackets under the white top, one on each side of the center cutout. Orient each bracket with the lower mounting flange shown in the close-up facing outward, then check the holes line up before inserting screws.

Match the bracket holes to the holes on the corresponding side of the tabletop.
Match the bracket holes to the holes on the corresponding side of the tabletop.
The presenter points to the bracket edge that faces outward under the tabletop.
The presenter points to the bracket edge that faces outward under the tabletop.

3. Seat all the small screws before tightening

Watch at 01:21

Start the small screws one at a time with the screwdriver and leave them loose enough to keep the holes aligned. Once all the screws on both brackets are seated correctly, go back and tighten them fully.

Start a small screw through the tabletop into the bracket below.
Start a small screw through the tabletop into the bracket below.
Check that the screws are seated on both sides of the center cutout.
Check that the screws are seated on both sides of the center cutout.
Tighten the small screws after they have all been started.
Tighten the small screws after they have all been started.

4. Seat the table below the machine plates

Watch at 02:04

Locate the four table mounting points on the machine. Bring the assembled table in from the front and seat the tabletop just below the metal plates. Look from underneath and shift the table until the four holes across the two brackets align with the four machine mounting points.

Locate the matching mounting points on the machine before lifting the table into place.
Locate the matching mounting points on the machine before lifting the table into place.
The white tabletop sits just below the machine's metal plate.
The white tabletop sits just below the machine's metal plate.
Check the holes from underneath where the bracket meets the machine.
Check the holes from underneath where the bracket meets the machine.

5. Fit the long screws at the rear and the short screws at the front

Watch at 03:03

Insert the two long knob screws in the rear holes and the two short knob screws in the front holes. Tighten all four and check that the working surface is securely seated and stable before setting the frame on it.

The diagram marks the rear pair for the long knobs and the front pair for the short knobs.
The diagram marks the rear pair for the long knobs and the front pair for the short knobs.
Tighten the mount from underneath the table.
Tighten the mount from underneath the table.
Check the installed table for stability before hooping.
Check the installed table for stability before hooping.

6. Prepare the fabric and lift off the magnets

Watch at 03:44

Set out the magnetic sash frame, its mounting screws, the fabric, backing, and scissors. The video uses cutaway stabilizer. Before attaching the bare frame to the machine, lift off all the magnetic bars. Grip a bar at one edge and lift it away, or use the lifting tool shown in the video.

The stabilizer, sash frame, fabric, and frame screws are ready.
The stabilizer, sash frame, fabric, and frame screws are ready.
Lift from one edge of a magnetic bar to release it.
Lift from one edge of a magnetic bar to release it.
The lifting tool helps raise the bar away from the metal frame.
The lifting tool helps raise the bar away from the metal frame.

7. Seat and fasten the bare sash frame

Watch at 04:25

Hold the metal frame level on the table. At each side of the rear carriage, match the locating pin to the corresponding frame hole and line up the screw holes. Slide the frame in so the pins seat. Insert a knob screw on each side and tighten both securely.

Match the pin and fastening hole on the rear carriage to the frame.
Match the pin and fastening hole on the rear carriage to the frame.
Hold the bare sash frame level as it slides onto both locating pins.
Hold the bare sash frame level as it slides onto both locating pins.
Tighten a frame knob on this side and repeat on the other side.
Tighten a frame knob on this side and repeat on the other side.

8. Cut the backing and lay the fabric over it

Watch at 04:58

Cut a piece of stabilizer slightly larger than the sash frame. Lay it over the mounted bottom frame, then place the fabric on top and adjust the area you want to embroider before adding the magnets.

Cut the stabilizer slightly larger than the frame with scissors.
Cut the stabilizer slightly larger than the frame with scissors.
Spread the cutaway backing over the metal bottom frame.
Spread the cutaway backing over the metal bottom frame.
Lay the fabric over the backing and smooth it into position.
Lay the fabric over the backing and smooth it into position.

9. Fit the magnetic bars with the arrows pointing inward

Watch at 05:16

Place the magnetic bars with their arrow marks pointing into the frame. Slide each bar into position along its edge. Once all four edges are held, check that the fabric is smooth, taut, and flat, with no wrinkles, folds, or loose areas in the stitching field.

Slide the front bar into place over the fabric and backing.
Slide the front bar into place over the fabric and backing.
Seat the right-side bar to hold the last open edge in the demonstration.
Seat the right-side bar to hold the last open edge in the demonstration.
Check the fabric within the four clamped edges is flat and taut.
Check the fabric within the four clamped edges is flat and taut.

10. Import the design and check its direction

Watch at 05:42

Power on the machine and wait for the design screen. Plug the drive into the USB port on the right side of the touchscreen, then tap the USB icon in the lower-right area of the design screen. Choose the file and confirm its import in the pattern dialog. Select the imported thumbnail, then check the design direction on the next settings page.

Insert the drive into the USB port on the right of the touchscreen.
Insert the drive into the USB port on the right of the touchscreen.
Tap the USB icon in the lower-right area of the design screen.
Tap the USB icon in the lower-right area of the design screen.
Check the pattern number and name in the import dialog, then tap the check mark.
Check the pattern number and name in the import dialog, then tap the check mark.
Select the floral design from the thumbnail list after importing.
Select the floral design from the thumbnail list after importing.
Check the design direction against the preview on the settings page.
Check the design direction against the preview on the settings page.

11. Check or change the color sequence on page 3

Watch at 06:09

Open page 3. The color sequence is on the left and the available needle colors are on the right. Select the color position you want to change, then tap the intended color on the right. The example replaces the first entry with yellow and then returns it to white. Compare the displayed sequence with the threads required for your design.

Choose the first entry in the color sequence on the left.
Choose the first entry in the color sequence on the left.
Tap the yellow swatch on the right for the example change.
Tap the yellow swatch on the right for the example change.
After restoring white, check the first sequence entry again.
After restoring white, check the first sequence entry again.

12. Select Magnetic Sash on page 4

Watch at 06:33

Open page 4 and tap the frame selector above the small buttons on the left. Select the Magnetic Sash preset in the list and confirm with the check mark. If the controller warns that the frame may move, clear the frame's travel area before confirming the warning. Back on page 4, check for the wide green frame and the design outline inside it.

Tap the frame selector above the group of buttons on the left.
Tap the frame selector above the group of buttons on the left.
The Magnetic Sash preset is highlighted in the frame list.
The Magnetic Sash preset is highlighted in the frame list.
The controller warns that the frame may move after selection.
The controller warns that the frame may move after selection.
The wide green frame shows the selected sash frame around the design outline.
The wide green frame shows the selected sash frame around the design outline.

13. Move the design with the arrow pad

Watch at 06:50

Use the arrow pad on the right of page 4 to shift the design position. The rabbit icon is the faster movement setting shown in the video. With the fabric clamped, use the next trace step to check the result on the actual fabric.

The directional pad on the right controls where the frame moves.
The directional pad on the right controls where the frame moves.
The center speed icon is shown while the video describes faster movement.
The center speed icon is shown while the video describes faster movement.

14. Trace the design on the fabric

Watch at 06:59

Tap the Trace control in the left-hand button group on page 4. Follow the frame as it moves around the stitch area without sewing. Check the trace stays in the intended area of the fabric and clears the metal frame and magnetic bars. If you reposition the design, run Trace again to check the new placement.

Tap Trace in the small button group on the left of page 4.
Tap Trace in the small button group on the left of page 4.
Watch the frame travel around the design area before any stitching starts.
Watch the frame travel around the design area before any stitching starts.
Check the moving frame and the clearance near the magnetic bars.
Check the moving frame and the clearance near the magnetic bars.

15. Choose automatic mode and set the speed

Watch at 07:24

Open the next page and choose automatic mode using the mode control shown in the lower-left button group. Set the stitching speed with the controls along the bottom of that group. The demonstration uses a setting of 800 stitches per minute.

The presenter points to the automatic mode control.
The presenter points to the automatic mode control.
The speed field between the blue decrease and increase controls is set to 800 in this example.
The speed field between the blue decrease and increase controls is set to 800 in this example.

16. Confirm embroidery and press the physical Start button

Watch at 07:40

Tap the embroidery confirmation control at the right end of the page tabs. The red control turns blue and the design appears in the stitch preview. Press the round blue-ring Start button below the touchscreen. The frame moves with the design and the first stitches appear on the fabric.

The finger points to the red embroidery confirmation control at the right end of the page tabs.
The finger points to the red embroidery confirmation control at the right end of the page tabs.
The confirmation control is blue and the presenter presses the blue-ring Start button below the screen.
The confirmation control is blue and the presenter presses the blue-ring Start button below the screen.
The first colors stitch inside the magnetic bars.
The first colors stitch inside the magnetic bars.

17. Check stitch progress and the finished design

Watch at 07:58

As sewing progresses, the controller preview fills in along with the stitches on the fabric. At the end, check that the complete design is in the intended position and the fabric is still held flat. The video shows the floral sample held up in the frame so you can see the full result.

The on-screen preview shows the colors already stitched as the design progresses.
The on-screen preview shows the colors already stitched as the design progresses.
The finished flowers and leaves are visible across the framed fabric.
The finished flowers and leaves are visible across the framed fabric.
The presenter holds up the finished design with the fabric still in the sash frame.
The presenter holds up the finished design with the fabric still in the sash frame.