SEWTECHSupport Center 简体中文

Assemble the ST-1501 Stand and Mount the Machine

Applies to ST-1501

Watch on YouTube ↗

Overview

Assemble the wheeled stand, fit the thread guide to the ST-1501, then mount the machine. Arrange for a second person to help turn the stand and lift the machine.

Step-by-step guide

1. Lay out the parts and tools

Watch at 00:17

Set out the two main frames, two slotted side support plates, storage shelf, four caster assemblies, four machine mounting pads, and fasteners. Get the Allen wrench and adjustable wrench from the toolbox. Set aside the four metal thread-guide rods for the work on the machine.

The stand parts, caster assemblies, fasteners, and pads are laid out beside the toolbox.
The stand parts, caster assemblies, fasteners, and pads are laid out beside the toolbox.
The presenter points to the toolbox for the wrenches.
The presenter points to the toolbox for the wrenches.

2. Orient the frames for the casters

Watch at 00:45

Set both main frames upside down with the sides that have the large holes facing up. Locate the four corners where the caster plates will sit.

The presenter points to the large-hole face of the frame.
The presenter points to the large-hole face of the frame.
The caster plate sits flat on the corner with its screw holes accessible.
The caster plate sits flat on the corner with its screw holes accessible.

3. Fit and tighten all four casters

Watch at 01:02

Place a caster at a corner and swivel the wheel slightly for access to the screw holes. Start the screws by hand, then fully tighten them with the Allen wrench. Repeat at the other three corners. Check that all four plates sit flush against the frames.

Start the caster screws by hand at the corners of the plate.
Start the caster screws by hand at the corners of the plate.
Use the Allen wrench on the started screws.
Use the Allen wrench on the started screws.
Four caster assemblies are now installed on the two frames.
Four caster assemblies are now installed on the two frames.

4. Align and fasten the storage shelf

Watch at 02:05

Keep the casters facing up. Hold the shelf between the two frames and bring the shelf and frame holes together. Hand-start the shelf screws as shown, then snug them lightly with the Allen wrench. Once all four are in, fully tighten them.

The shelf is held between the two inverted frames.
The shelf is held between the two inverted frames.
Bring the hole at the shelf corner in line with the frame attachment point.
Bring the hole at the shelf corner in line with the frame attachment point.
The Allen wrench is used after hand-starting the screw.
The Allen wrench is used after hand-starting the screw.
Finish tightening at the shelf corners once all four screws are fitted.
Finish tightening at the shelf corners once all four screws are fitted.

5. Fasten both side support plates

Watch at 03:09

Hold one slotted support plate across an open side of the stand. Match its four corner holes to the holes in the frames and start all four screws by hand. Tighten them with the Allen wrench once the plate sits in place. Fit the plate on the opposite side the same way.

Hold the first plate across the opening and match the four corners.
Hold the first plate across the opening and match the four corners.
Tighten the first plate after all four screws are in place.
Tighten the first plate after all four screws are in place.
Start the fasteners on the second plate the same way.
Start the fasteners on the second plate the same way.
The second plate is seated against the frames.
The second plate is seated against the frames.

6. Turn the stand upright

Watch at 04:07

With the shelf and both plates secured, have two people grip opposite sides and turn the empty stand over as shown. Set it down with all four casters underneath and the two machine-mounting rails on top.

Two people take hold from opposite sides before turning the stand.
Two people take hold from opposite sides before turning the stand.
The stand is upright with the casters under the frame.
The stand is upright with the casters under the frame.

7. Install the four thread-guide rods

Watch at 04:26

Fit the rods to the machine before lifting it onto the stand. Identify the spacer end of each rod and keep it down. Remove the screw from that end. Have a helper lift the guide plate enough to clear the work area. Insert the screw upward through the mounting plate below the thread cones, then spin the rod onto it by hand. Repeat at all four positions and tighten the lower screws with the Allen wrench.

The collar at this end identifies the spacer side that faces down.
The collar at this end identifies the spacer side that faces down.
The guide plate is held up while the first rod is fitted above the lower screw.
The guide plate is held up while the first rod is fitted above the lower screw.
Fit the remaining rods at the mounting points beside the thread cones.
Fit the remaining rods at the mounting points beside the thread cones.
The Allen wrench tightens a lower screw from underneath.
The Allen wrench tightens a lower screw from underneath.

8. Secure the thread guide plate

Watch at 05:15

Remove the four screws from the tops of the rods. Lower the guide plate onto the rods and align the four holes. Insert the saved screws through the plate and tighten them with the Allen wrench. Check that the plate sits on all four rods.

Remove the screw at each rod top before lowering the plate.
Remove the screw at each rod top before lowering the plate.
The guide plate is lowered onto the four rod ends.
The guide plate is lowered onto the four rod ends.
The Allen wrench tightens a screw through the upper guide plate.
The Allen wrench tightens a screw through the upper guide plate.

9. Lower the four leveling feet

Watch at 06:17

Roll the empty stand into its working position. Turn down the round threaded foot next to each caster until it bears firmly on the floor. Check all four corners before loading the stand. The feet should carry the stand so it stays put. To roll it again later, turn the feet up until the casters can carry the stand.

Turn the round foot beside the caster down by hand.
Turn the round foot beside the caster down by hand.
The close-up shows the threaded foot bearing on the floor.
The close-up shows the threaded foot bearing on the floor.
Repeat the adjustment at every corner.
Repeat the adjustment at every corner.

10. Align the four mounting pads with the outer holes

Watch at 06:55

Lay one pad flat on each upper corner of the stand. Each corner has two holes. Center the pad over the hole closest to the end of the rail, as shown by the arrow. Check the position of all four pads before lifting the machine.

The arrows mark the four corners that receive a mounting pad.
The arrows mark the four corners that receive a mounting pad.
Center the pad on the outer hole at the end of each rail.
Center the pad on the outer hole at the end of each rail.

11. Lift the machine onto the stand

Watch at 07:09

With a second person, support the machine from the underside of its base as shown. Lift it over the stand and lower it carefully onto the four pads. Align the holes in the bottom of the machine base with the holes through the pads and stand. Check that the feet of the machine base sit squarely on the pads.

The inset points out a mounting hole on the underside of the machine base.
The inset points out a mounting hole on the underside of the machine base.
The two people support the machine from its base.
The two people support the machine from its base.
The machine foot settles squarely onto the mounting pad.
The machine foot settles squarely onto the mounting pad.

12. Start all four mounting bolts from below

Watch at 07:43

Use the four machine mounting bolts with the spacer and washer shown in the close-up. Reach under the top rail at each corner and insert the bolt upward into the aligned mounting hole. Start each bolt by hand. Check that all four have engaged before tightening with the wrench.

The machine mounting bolt has a spacer and washer under its head.
The machine mounting bolt has a spacer and washer under its head.
Start the bolt upward through the rail from below.
Start the bolt upward through the rail from below.
Hand-start the bolts at the remaining corners.
Hand-start the bolts at the remaining corners.

13. Tighten the bolts and check the assembly

Watch at 08:15

Use the adjustable wrench from under the stand to fully tighten all four machine mounting bolts. Before using the machine, check that the base sits on the pads, each bolt is tight, and all four leveling feet bear firmly on the floor. Finish with the stand steady in its working position.

Switch to the adjustable wrench after all four bolts have been started.
Switch to the adjustable wrench after all four bolts have been started.
Tighten the mounting bolt from underneath the top rail.
Tighten the mounting bolt from underneath the top rail.
The installed guide plate sits above the machine head.
The installed guide plate sits above the machine head.