Troubleshoot Thread Breaks on the ST-1201 and SC-1501
Overview
If the machine repeatedly stops with thread breaks, start with the bobbin, then check the needle and the upper thread path. The video demonstrates the checks on the ST-1201. Stop the machine before handling the bobbin, needle or thread. Have a wound spare bobbin, a small flat-blade screwdriver and a suitable replacement needle at hand.
Step-by-step guide
1. Open the bobbin cover and check for thread
Watch at 00:31With the machine stopped, open the front cover directly below the needle plate and pull out the bobbin case. Take the bobbin out of the case to see whether it has thread left. If it is empty, put a fully wound bobbin into the case and draw the thread tail through the case slot and under the tension spring before testing.



2. Hang the case by the thread
Watch at 00:49Pinch the loose thread end and let the loaded case hang freely. Keep your other hand underneath as a catch. A case that hardly drops, or descends only slowly even after a firmer shake, has too much bobbin tension.


3. Loosen the larger screw in small steps
Watch at 01:05On the side of the bobbin case, locate the larger slotted screw on the tension spring. With a small flat-blade screwdriver, turn it counterclockwise about 1/10 to 1/8 of a turn. Hang the case again after each adjustment and repeat only as needed.


4. Retest for a short, smooth drop
Watch at 01:29Give the hanging case a gentle flick of the wrist. The video's criterion is a smooth drop of about 3–5 cm (roughly 1–2 in), followed by a stop on its own. Watch the case relative to the thread pinched in your fingers and keep your lower hand beneath it.


5. Reinstall the bobbin case
Watch at 01:32Guide the loaded case straight back into the hook opening under the needle plate. Seat it fully, then close the front cover before moving on to the needle checks.


6. Identify the front and back of the needle
Watch at 01:41At the front of the stationary needle head, inspect the needle fitted at the problem position. The long thread groove should face you. The scarf, the small recess just above the eye on the other side, should face the machine.


7. Seat the needle fully and tighten its screw
Watch at 02:02If the needle sits too low or is out of position, support it while loosening the clamp screw next to that needle shank. Keeping the long groove forward, push the needle up as far as it will go into the needle bar. Hold it there while tightening the screw. Check the seating of the other needles too.



8. Replace a worn needle
Watch at 02:13If the needle has been in use for a long time and is worn, fit a new one suitable for your machine. Keep the same orientation, seat it fully and secure the clamp screw. A worn needle can contribute to thread breaks or needle breakage.

9. Pull the upper thread gently to locate drag
Watch at 02:31With the machine stopped, take the upper thread end for the problem needle and pull it gently by hand. If it is unusually hard to pull or catches, trace that thread from its spool to the needle to find where it binds or leaves its intended path.


10. Free thread trapped at the spool cap
Watch at 02:50Find the same thread's cone on the spool stand. Lift the cone and check around its holder and cap. Free any trapped strand, return the cone to its holder and rethread it so it can feed freely into the overhead guide.


11. Follow the guide tube into the tension discs
Watch at 03:01Follow the thread up to the guide rack and through the matching clear tube. At the top of the thread panel, check that it enters between the tension discs for the same needle and feeds through them smoothly.


12. Adjust the top-row knob slightly if needed
Watch at 03:15If the thread is routed correctly but still pulls with the wrong tension, use the top-row knob for that needle. Turn it a little clockwise to tighten or counterclockwise to loosen. Pull the thread again to judge the change before making another adjustment.

13. Wrap the large wheel one and a half turns
Watch at 03:23Farther down the panel, follow the thread around its large black wheel with the light-colored rim in the two staggered rows. Check for one full turn plus a half turn before the thread continues down through the next guide.


14. Follow every lower guide and hole
Watch at 03:30Continue down the same thread path. Check that the thread stays in its guides, passes through its take-up lever and lower eyelets, and continues to the needle eye. Follow each point in order so the thread cannot bypass a guide or catch on the way down.



15. Pull again to confirm smooth feeding
Watch at 03:42Return to the same needle end and gently pull the thread by hand again. It should draw through the full route smoothly, without sticking or suddenly tightening. If it still catches, find and clear the tight point before sewing.

16. Run a short test stitch
Watch at 03:50Keep hands clear of the head and run a short test on hooped material. Watch for continuous thread feeding and a section of stitches that forms without another thread-break stop. The clip shows a red S on white fabric as the test example.

