SEWTECHSupport Center 简体中文

Embroider a Shoe with the ST-1501 Shoe Clamp

Applies to ST-1501

Watch on YouTube ↗

Overview

Use the SEWTECH ST-1501 and shoe clamp to embroider the outside ankle panel of a high-top sneaker. Have a shoe, adhesive embroidery stabilizer, a 3 mm Allen wrench, scissors, and a washable marking pen ready. The design needs to fit the flat area between the clamp arms. Watch the full laser trace before you start stitching.

Step-by-step guide

1. Find and mark the embroidery center

Watch at 00:25

Lay the shoe on its side. Place a template the size of your design on the flat outside ankle panel to see the area the needle will cover. Check how that footprint sits next to the eyelets and sole, then mark its center with the washable pen.

The black template shows the design footprint on the outside ankle panel.
The black template shows the design footprint on the outside ankle panel.
The pen marks the center on the shoe upper after the template is lifted.
The pen marks the center on the shoe upper after the template is lifted.

2. Apply adhesive stabilizer inside the shoe

Watch at 00:42

Cut a piece of adhesive stabilizer slightly larger than the design. Peel off the release paper and stick the adhesive side to the inside of the upper, directly behind the marked area. Press it flat from inside the shoe and smooth out wrinkles. Check that it covers the entire design footprint.

Cut around the template with room to spare on all sides.
Cut around the template with room to spare on all sides.
Peel the release paper away to expose the adhesive side.
Peel the release paper away to expose the adhesive side.
Press behind the intended design area from inside the upper.
Press behind the intended design area from inside the upper.

3. Set the support-arm spacing

Watch at 01:11

Loosen the two black adjustment knobs on the blue mounting bar, slide the support arms to suit the shoe, then retighten the knobs to hold that spacing. The small black-handled levers next to the arms open and close the jaws for loading and securing the upper.

The black knobs at the bases of the arms let them slide along the bar.
The black knobs at the bases of the arms let them slide along the bar.
The small levers open the blue jaws away from the lower support arms.
The small levers open the blue jaws away from the lower support arms.

4. Mount the shoe clamp under the ruler

Watch at 01:44

Use the 3 mm Allen wrench to loosen the mounting screws. Fit the blue mounting bar between the two metal plates under the machine ruler. Line the screw hole up with the first slot indicated in the video, seat the bar, and tighten both mounting screws. Check that both ends of the bar are secure.

Use the 3 mm Allen wrench on the mounting screw shown in the inset.
Use the 3 mm Allen wrench on the mounting screw shown in the inset.
Lift the blue mounting bar into place with an arm on each side of the bobbin area.
Lift the blue mounting bar into place with an arm on each side of the bobbin area.
The red arrow identifies the first slot under the ruler.
The red arrow identifies the first slot under the ruler.
The wrench tightens the screw on one end of the seated bar.
The wrench tightens the screw on one end of the seated bar.
Tighten the other mounting screw under the ruler as well.
Tighten the other mounting screw under the ruler as well.

5. Check the bobbin before loading the shoe

Watch at 02:19

Open the cover at the front of the bobbin arm and pull the bobbin case out. If the thread is low or has run out, fit a full bobbin in the case. Put the case back in the machine and close the cover before loading the shoe.

The lowered cover exposes the bobbin case, which lifts out by its latch.
The lowered cover exposes the bobbin case, which lifts out by its latch.
The full white bobbin is ready to go into the case.
The full white bobbin is ready to go into the case.
Slide the loaded case back into the front of the bobbin arm.
Slide the loaded case back into the front of the bobbin arm.

6. Select the design, direction and colors

Watch at 02:44

Turn on the machine. On controller page 1, tap the design thumbnail. Open page 2 and use Direction to set how the design will sit on the shoe. On page 3, check the color sequence on the left and use the numbered needle palette on the right to assign colors. Check the design preview before moving on.

Tap the design thumbnail on page 1.
Tap the design thumbnail on page 1.
Direction is in the left column on page 2, below the design preview.
Direction is in the left column on page 2, below the design preview.
On page 3, the color sequence is on the left and the numbered needle palette is on the right.
On page 3, the color sequence is on the left and the numbered needle palette is on the right.

7. Select None Frame on page 4

Watch at 03:05

Open controller page 4 and tap the frame field on the left, above the trace controls. On the frame selection screen, choose None Frame at the bottom and tap the check mark. The frame field should now read frame none. You will check clearance on the shoe itself with the laser trace.

The frame field is below the green frame preview, above the left-hand controls.
The frame field is below the green frame preview, above the left-hand controls.
None Frame is the button at the bottom of the frame selection screen.
None Frame is the button at the bottom of the frame selection screen.
The check mark is immediately to the right of None Frame.
The check mark is immediately to the right of None Frame.
The page returns without a frame outline after you confirm None Frame.
The page returns without a frame outline after you confirm None Frame.

8. Open the clamp and adjust it to the shoe

Watch at 03:13

Turn the small black handles to open the jaws. If the arms need repositioning, loosen the two larger black knobs on the mounting bar, slide the support arms to suit the usable flat area of the upper, then tighten the knobs again. Leave room for the design between the arms.

The small black handle beside the arm opens the jaw.
The small black handle beside the arm opens the jaw.
The larger knobs on the bar let you move the arms sideways.
The larger knobs on the bar let you move the arms sideways.
The arrows point to the two lower support arms beside the bobbin arm.
The arrows point to the two lower support arms beside the bobbin arm.

9. Slide in the shoe and lock it flat

Watch at 03:35

Hold the shoe with the marked panel facing up. Guide it past the bobbin arm and slide the panel between the open jaws, with the mark visible between the two blue arms. Make sure the shoe clears the bobbin area. Lock the levers and check that the upper lies flat and the shoe stays firmly in place.

Slide the upper into the open clamp with the marked panel facing the needles.
Slide the upper into the open clamp with the marked panel facing the needles.
The side view shows how the shoe passes around the bobbin arm.
The side view shows how the shoe passes around the bobbin arm.
The marked center is visible between the blue arms.
The marked center is visible between the blue arms.
Hold the shoe steady while closing the lever.
Hold the shoe steady while closing the lever.

10. Trace the full design outline with the laser

Watch at 03:59

On page 4, tap Trace, the rightmost icon in the first row of small buttons under the frame field. Tap the check mark in the prompt to move along the design outline. Watch the red laser dot throughout the trace. The entire path must stay on the supported upper between the clamp arms, with clearance from the metal jaws and the bobbin area.

The rightmost icon in the top row of small buttons starts outline tracing.
The rightmost icon in the top row of small buttons starts outline tracing.
Tap the check mark in the prompt to start the outline movement.
Tap the check mark in the prompt to start the outline movement.
Watch the red laser dot and its clearance from both clamp arms.
Watch the red laser dot and its clearance from both clamp arms.

11. Fine-tune placement with the arrow keys

Watch at 04:17

Use the direction arrows on the right to shift the design toward your center mark. Tap the center speed control to switch between Rabbit for faster movement and Turtle for smaller, slower adjustments. Run the trace again after moving the design and check the full path before confirming embroidery.

Tap the arrows on the right to move the placement.
Tap the arrows on the right to move the placement.
Tap the center speed control to select Rabbit for faster moves.
Tap the center speed control to select Rabbit for faster moves.
Select Turtle with the same control for slower fine adjustments.
Select Turtle with the same control for slower fine adjustments.

12. Confirm embroidery on the touchscreen

Watch at 04:28

After the clearance check, tap the fifth tab in the middle strip to open the embroidery screen. Tap the far-right red sewing-mode button in the same strip. In the Confirm EMB? dialog, tap the blue check mark. The mode button turns blue and the design preview reappears when the machine is ready for Start.

The fifth tab opens the embroidery controls.
The fifth tab opens the embroidery controls.
Tap the red sewing-mode control at the far right of the middle strip.
Tap the red sewing-mode control at the far right of the middle strip.
In the Confirm EMB? dialog, tap the blue check mark.
In the Confirm EMB? dialog, tap the blue check mark.
The preview returns and the far-right mode control turns blue.
The preview returns and the far-right mode control turns blue.

13. Press the blue-ringed Start button

Watch at 04:35

Press the blue-ringed Start button below the touchscreen. The machine starts stitching inside the two blue arms. Watch the first stitches form on the backed panel and check that the shoe remains flat and held securely as the design builds.

The blue-ringed physical Start button is below the touch panel on the left.
The blue-ringed physical Start button is below the touch panel on the left.
The first stitches form on the flat upper between the blue arms.
The first stitches form on the flat upper between the blue arms.
The arms continue to hold the upper while the outline is stitched.
The arms continue to hold the upper while the outline is stitched.

14. Wait for completion and remove the shoe

Watch at 05:17

Wait for the machine to stop and for the screen to show Embroidery completed! Support the shoe by the sole, unlock the clamp levers, then guide it out from under the needle head. Inspect the finished motif on the outside ankle panel.

Embroidery completed! confirms the run is finished.
Embroidery completed! confirms the run is finished.
Hold the sole while unlocking the clamp lever.
Hold the sole while unlocking the clamp lever.
The finished motif is on the flat outside ankle panel.
The finished motif is on the flat outside ankle panel.