SEWTECHSupport Center 简体中文

Fix a False Thread Break Alarm on the ST-1201 and SC-1501

Applies to ST-1201 / SC-1501 Demonstrated on ST-1201

Watch on YouTube ↗

Overview

If an intact upper thread triggers a Broken Line alert, inspect the threading path first, then check the bobbin and how its thread feeds. After correcting the problem, back up a few stitches and watch the design resume. The video demonstrates the procedure on the ST-1201.

Step-by-step guide

1. Confirm the alarm and the affected needle

Watch at 00:11

Use this procedure when the machine has stopped with a Broken Line alert and the upper thread is still intact. Read the Head and Needle fields in the alert, then check the thread for that needle while the machine is stopped. The ST-1201 in the video shows Head 1 and Needle 3. Use the numbers on your own screen.

The Broken Line alert identifies the affected head and needle.
The Broken Line alert identifies the affected head and needle.

2. Trace the upper thread through its guides

Watch at 00:24

Follow the affected thread from the needle area up the front of the head. Check that it runs through each guide opening in its own path. The pointer starts below the head at the needle bank and moves up to the vertical threads and guides.

Start at the needle bank just above the hooped fabric.
Start at the needle bank just above the hooped fabric.
Continue through the corresponding guides above the vertical thread paths.
Continue through the corresponding guides above the vertical thread paths.

3. Check the one-and-a-half-turn wrap

Watch at 00:33

Follow the pointer to the larger black wheel in the lower row on the front of the ST-1201 threading panel. Follow the demonstrated path and wrap the thread one and a half turns around the wheel for the affected thread path. Continue with the sensor wheel above it.

The pointer marks the larger lower-row wheel as the presenter specifies one and a half turns.
The pointer marks the larger lower-row wheel as the presenter specifies one and a half turns.

4. Reseat the thread on the break sensor wheel

Watch at 00:42

Look above the large wheels for the row of small dotted sensor wheels. On the affected path, check that the thread sits around the rim of its sensor wheel. The close-up shows a misplaced thread. Guide the strand back onto the wheel and check that it follows the rim before you move on.

The pointer identifies the dotted row of break sensor wheels.
The pointer identifies the dotted row of break sensor wheels.
The presenter lifts the loose strand at the sensor wheel to correct its path.
The presenter lifts the loose strand at the sensor wheel to correct its path.
After rethreading, the strand follows the edge of the dotted wheel.
After rethreading, the strand follows the edge of the dotted wheel.

5. Check where the thread sits in the top tension knob

Watch at 00:56

Find the affected thread at the top row of black tension knobs directly below the clear guide tubes. Seat the strand between the tension discs behind its knob. Then check the feed by hand in the next step.

The fingertip points to the thread where it enters the top tension knob assembly.
The fingertip points to the thread where it enters the top tension knob assembly.

6. Pull gently, clear any snag and test again

Watch at 01:09

Hold the thread end near the needles and pull gently. It should feed smoothly without catching. If it feels tight or stalls, follow the same thread up through the front guides, tension area and clear guide tube to look for a snag. The video shows the upper end of the tube being lifted at the rack to free a trapped strand. Gently pull again at the needle area to confirm that it feeds freely.

Pull the thread end by hand near the needle bank to feel whether it catches.
Pull the thread end by hand near the needle bank to feel whether it catches.
The top of the clear guide tube is lifted at the support rack to reach the trapped strand.
The top of the clear guide tube is lifted at the support rack to reach the trapped strand.
Repeat the gentle pull near the needles after clearing the path.
Repeat the gentle pull near the needles after clearing the path.

7. Open the lower cover and check whether the bobbin is empty

Watch at 01:46

With the machine still stopped, open the hinged cover below the hoop and pull out the bobbin case by its center latch. If the bobbin has run out of thread, replace it with a wound bobbin. If it still has thread but the machine failed to pick it up, reload it as shown in the next step.

The lower cover swings down to expose the bobbin case below the hoop.
The lower cover swings down to expose the bobbin case below the hoop.
The center latch is where the presenter grips the case to remove it.
The center latch is where the presenter grips the case to remove it.
The presenter shows a wound bobbin for replacement.
The presenter shows a wound bobbin for replacement.

8. Reload the bobbin case and leave a thread tail

Watch at 02:02

Place the wound bobbin into the case and draw the thread through the side slot, following the path under the tension spring shown in the close-up. Pull out some extra thread so a tail extends past the case for pickup. Push the case back into the compartment and close the cover.

Seat the bobbin inside the metal case with the loose end accessible.
Seat the bobbin inside the metal case with the loose end accessible.
Draw the thread through the side slot and under the case spring.
Draw the thread through the side slot and under the case spring.
Leave a visible length of thread outside the case for pickup.
Leave a visible length of thread outside the case for pickup.
With the case back in the compartment, lift the cover to close it.
With the case back in the compartment, lift the cover to close it.

9. Back up to the last stitched area

Watch at 02:26

On the ST-1201 screen, tap the upper-right button in the six-button block to the left of the directional pad. Choose a short increment in the stitch-move controls. The display changes from 100 to 5 in the demonstration. Tap the minus button at the lower left to back up to the last area that stitched correctly. Then tap the return icon at the lower right to close the controls.

Tap the upper-right button in the group of six to open the stitch-move controls.
Tap the upper-right button in the group of six to open the stitch-move controls.
The presenter uses the lower-left minus button with the increment set to 5 in this example.
The presenter uses the lower-left minus button with the increment set to 5 in this example.
Tap the return icon at the lower right to return to the main screen.
Tap the return icon at the lower right to return to the main screen.

10. Restart and check the first stitches

Watch at 02:34

With the bobbin cover closed and hands clear, press the left, blue-ringed Start button below the touchscreen. Watch the first stitches where the design resumes. The video shows the needle stitching again. Check that the thread feeds, stitches form at the restart point and the alarm does not immediately return.

Press the blue-ringed physical Start button below the display.
Press the blue-ringed physical Start button below the display.
The needle resumes stitching in the same hooped design.
The needle resumes stitching in the same hooped design.