Embroider a Cap on the ST-1501
Overview
This SEWTECH ST-1501 tutorial shows how to hoop a cap on the table station, fit the cap driver, choose the cap frame on the touchscreen and trace the design against the actual needle before stitching. The example places a multicolor design on the center front of a black cap.
Step-by-step guide
1. Prepare the cap embroidery parts
Watch at 00:20Gather a cap driver, a table-mounted cap station, a cap hoop, a cap, stabilizer, and a screwdriver. Have scissors for cutting the backing and clips for securing the back of the cap. The driver moves the hoop on the machine. The station holds the hoop steady while you load it. The hoop holds the cap and stabilizer during sewing. The video shows two hoops so you can prepare the next cap while the first one stitches.


2. Clamp the station to a flat table
Watch at 01:23Use a flat, stable tabletop. Turn the knob below the station to open the clamp to the tabletop thickness, slide the clamp over the edge, and tighten it fully from below. Gently shake the station to check it stays put.



3. Lock the empty hoop onto the station
Watch at 02:10Unlatch the metal retaining band and move it out of the way. Slide the hoop over the curved station and align its latch with the station's alignment block. Press forward with both hands until it clicks. Check the two upper clips and the one underneath. To release the hoop, press all three clips together and slide it off.




4. Cut and place the backing
Watch at 03:23Cut a piece of tear-away stabilizer. For this front design, cover the whole front panel. For side embroidery, use a longer piece that reaches the side area. Lay the backing over the curved station under the cap position and seat the near edge at the center guide as shown.



5. Seat the sweatband and align the cap
Watch at 04:26Turn the sweatband outward and slip its front under the center guide. Line up the front seam with the hoop mark, then shift the seam slightly left as shown before closing the band. The strap pulls it back toward center as it closes. Smooth the sweatband over the hoop and pull the back of the cap over both support rods.




6. Close the retaining band and recheck the seam
Watch at 05:36Bring the retaining band around the cap so its wire catches the lower seam where the front meets the brim. Engage the clasp on the right and press it down. Check that the cap seam now lines up with the hoop mark and the front panel is smooth.



7. Adjust the band if the latch will not reach
Watch at 06:14If the band is too short or tight to close, loosen the three screws at the band end with a screwdriver. Slide the band a little to suit the cap, retighten all three screws and try the clasp again. The band should close and hold the cap firmly.



8. Clip the back and release the loaded hoop
Watch at 07:04Use clips to secure the lower back of the cap over the rear supports. Hold the hoop on both sides, press the station's three release clips together and slide off the loaded hoop as a unit.



9. Select the cap profile and switch off before fitting the driver
Watch at 07:28Select the cap frame profile on the control panel while it is powered. Stop the machine and turn it off at the power switch before handling or fitting the driver. The video repeats the frame selection after power-up and shows the touchscreen selection there.


10. Loosen the two mounting screws and turn the driver wheels up
Watch at 07:50Loosen the two mounting screws on the driver's long bar. Support the driver with both hands, turn it into the middle under the needle head, then rotate the wheel bracket so its four wheels face up.



11. Seat all four wheels in the two rails
Watch at 08:44Bring the driver up to the machine arm so the wheels line up with the rails on both sides. Check that all four wheels enter the tracks, then push the driver into place.



12. Align the mounting plate and tighten both sides
Watch at 09:08Locate the mounting hole on each side. The demonstration counts to hole 8 on the machine shown. Start both screws with a screwdriver and leave them slightly loose. Push the plate in squarely against the machine arm, check both sides are seated, then fully tighten both screws.




13. Power on and reselect Cap Frame 270 × 70
Watch at 10:17After the driver is secured, turn on the ST-1501. On the fourth touchscreen tab, open the frame selector above the trace buttons. Select Cap Frame 270 × 70 and tap the checkmark. The warning says the frame may move. Make sure the driver's path is clear, then confirm. Check that the preview changes to the long, narrow cap field and the selector reads Cap Frame.



14. Check the bobbin before mounting the cap
Watch at 10:42With the machine idle, check the bobbin in the case at the end of the machine arm, inside the driver opening. Replace a low bobbin before the cap hoop blocks access. The presenter shows a full bobbin, then puts the case back in.



15. Mount the loaded hoop and check all three clips
Watch at 11:08Rotate the loaded hoop sideways so the cap and brim can pass into the driver opening. Then turn the hoop into its stitching position and push both sides in together. Check that the hoop is fully seated and all three clips have locked before moving the frame.



16. Select the design from machine memory
Watch at 11:44Open the leftmost design tab and tap the design thumbnail. The example uses pattern 455, the multicolor Love design in the second row. Check the selected number under the thumbnails before continuing.


17. Assign the thread colors
Watch at 11:53Open the third tab for color order. Select the first color block in the list on the left, then tap the numbered swatch for the needle carrying red thread on this machine. The first block and the Love preview turn red. The video leaves the remaining colors as shown. Match the on-screen assignments to the thread loaded on your own machine.



18. Move the design inside the cap field
Watch at 12:15Open the fourth tab and use the arrows on the right to move the design toward the center of the cap field for a front placement. The screen fills the field pink-red and shows a warning when the design extends beyond the usable area. Move it back until the warning clears and the green frame outline has a clear interior. Then check the actual placement by tracing on the cap.



19. Switch the active needle to No. 1 before tracing
Watch at 13:07Open the needle-position controls using the needle icon in the bottom toolbar. The demonstration starts with No. 8 active. Tap No. 1 at the right end of the top row, wait for the head to shift to that needle, and use the lower-right return button to leave the needle screen. This selects the active needle for tracing. The earlier color assignments control the stitching sequence.



20. Trace the outline with the actual needle position
Watch at 13:33Return to the fourth tab and tap the rightmost button in the top row of trace tools, the needle with a dotted outline. Watch where No. 1 passes over the cap as the driver moves. At the end, the driver returns to the design center. Check that the needle lines up with the cap's center seam. If it is off-center, adjust with the arrows and run the trace again. Use the needle itself as the reference on the curved cap, even when a red laser dot is visible.



21. Set the speed and confirm the design
Watch at 14:33Open the fifth tab for embroidery controls. Use the minus and plus buttons below the controls to set the speed. The tutorial recommends 650 stitches per minute for the cap shown. Tap the far-right red icon to open Confirm EMB?, then tap the checkmark. Wait for the loading screen to clear and the embroidery progress preview to appear.



22. Start stitching with the blue-ring button
Watch at 14:46Keep hands clear of the needle and driver, then press the left physical button with the blue ring under the screen. Check that the needle starts stitching and the cap driver moves the loaded hoop. The first visible stitches in this sample are red. During sewing, the progress view shows the design upside down, matching the cap's orientation on the driver.



23. Wait for stitching to finish and remove the hoop
Watch at 15:49Wait for the Embroidery completed! message and make sure the needle and hoop have stopped. Support the hoop with both hands, press its three release clips together and slide the loaded hoop away from the driver. Check the finished design on the front panel against the cap's center seam. The video shows the finished cap after removal.




