SEWTECHSupport Center 简体中文

Move Forward or Back by Stitches on the ST-1501

Applies to ST-1501

Watch on YouTube ↗

Overview

Use this guide when the SEWTECH ST-1501 has stopped after a thread break. Leave the design loaded and the hoop attached. Rethread the active needle, then use a fixed stitch count or continuous movement to return to the break. Use the single-stitch controls for the final adjustment before resuming.

Step-by-step guide

1. Check where the thread broke

Watch at 00:10

Wait until embroidery has stopped. Look at the stitches under the active needle. The controller may advance a few stitches before the machine stops, so fabric can be left unstitched between the last complete stitch and the current position. Keep the hoop in place so you can find that gap.

The opening example shows the hoop and the part-stitched letter F under the needle head.
The opening example shows the hoop and the part-stitched letter F under the needle head.
Inspect the stitched area below the active needle before repositioning.
Inspect the stitched area below the active needle before repositioning.

2. Rethread the active needle

Watch at 00:29

With the machine stopped, thread the broken upper thread back through the eye of the active needle. The example shows the operator working directly below the needle bar while the same fabric stays in the hoop.

The operator guides the upper thread back through the active needle area.
The operator guides the upper thread back through the active needle area.
The hands draw the thread through while the hooped design stays in place.
The hands draw the thread through while the hooped design stays in place.

3. Open the stitch controls and set a count

Watch at 00:34

On the embroidery screen, tap the top-right key in the six-key block to the left of the direction pad. On the stitch controls screen, tap the number between the lower − and + buttons. The Number Pad opens. Enter the distance to move in the Goto Stitches field and tap the blue checkmark. The example changes the count from 100 to 10. Check that the new count appears between the two buttons.

The fingertip marks the key that opens the stitch controls from the embroidery screen.
The fingertip marks the key that opens the stitch controls from the embroidery screen.
Tap the count between the lower − and + buttons to open the keypad.
Tap the count between the lower − and + buttons to open the keypad.
The Number Pad shows 10 in the Goto Stitches field for this demonstration.
The Number Pad shows 10 in the Goto Stitches field for this demonstration.
Tap the blue checkmark to save the count and close the keypad.
Tap the blue checkmark to save the count and close the keypad.

4. Lower the presser foot to find the stitch

Watch at 00:53

With the machine stopped, lower the presser foot at the active needle as shown. Use the foot over the fabric as a visual reference when finding the end of the sewn stitches. Keep your hands clear of the needle area when you move the hoop or resume stitching.

The finger points to the presser foot directly above the stitched design.
The finger points to the presser foot directly above the stitched design.
Use the lowered foot over the fabric to compare the needle position with the sewn stitches.
Use the lowered foot over the fabric to compare the needle position with the sewn stitches.

5. Move back or forward by the set count

Watch at 00:59

Tap the lower − button immediately left of the count to move back by that many stitches. Compare the position over the fabric with the last complete stitches and repeat as needed. If you go back too far, tap the + button on the other side of the count to move forward by the same amount. Use single-stitch movement as you approach the break.

The lower − button to the left of 10 moves back by the selected count.
The lower − button to the left of 10 moves back by the selected count.
The inset shows the foot over the embroidered F while the touchscreen is used to go back.
The inset shows the foot over the embroidered F while the touchscreen is used to go back.
The lower + button just to the right of 10 moves forward by the same count.
The lower + button just to the right of 10 moves forward by the same count.

6. Fine-tune one stitch at a time

Watch at 01:13

Use the left pair marked −1 and +1 on the row above the count. Tap −1 to go back one stitch or +1 to go forward one stitch. Check the position after each tap until you reach the break point.

The left-side +1 key on the middle row moves forward one stitch.
The left-side +1 key on the middle row moves forward one stitch.
The −1 key immediately to its left moves back one stitch.
The −1 key immediately to its left moves back one stitch.

7. Run continuous reverse and stop at the break

Watch at 01:20

For continuous movement, rethread first and lower the presser foot in the same way. On the stitch controls panel, tap the − in the top-left pair to start moving backward. Watch the position over the fabric and the changing stitch path in the design preview. Tap the same − again as you reach the break to stop the movement.

The same lowered foot is used as the reference for continuous movement.
The same lowered foot is used as the reference for continuous movement.
The arrow marks the upper left − button for continuous reverse.
The arrow marks the upper left − button for continuous reverse.
The two insets compare the stitch path in the preview and the position on the fabric.
The two insets compare the stitch path in the preview and the position on the fabric.
The operator taps the same upper − button again to stop.
The operator taps the same upper − button again to stop.

8. Use continuous forward to correct an overshoot

Watch at 01:38

If you reversed past the break, tap + beside the continuous reverse key on the top left. Watch the preview and the fabric together as the position moves forward. Tap the same + again to stop at the intended stitch.

The arrow identifies the upper + button immediately beside continuous reverse.
The arrow identifies the upper + button immediately beside continuous reverse.
The design inset and the fabric help you judge when to stop.
The design inset and the fabric help you judge when to stop.
The crosshair in the enlarged preview shows the selected stitch after forward movement.
The crosshair in the enlarged preview shows the selected stitch after forward movement.

9. Check the restart point and correct one stitch

Watch at 01:50

Compare the current point in the stitch preview with the end of the sewn line on the fabric. If continuous forward took you one stitch too far, use the −1 key on the left of the middle row to move back one stitch. Confirm the foot lines up with the point where the missing stitches begin.

The finger points to the stitch information below the design preview.
The finger points to the stitch information below the design preview.
The operator uses the middle-row −1 to correct a one-stitch overshoot.
The operator uses the middle-row −1 to correct a one-stitch overshoot.
The inset shows the selected position on the fabric after a one-stitch correction.
The inset shows the selected position on the fabric after a one-stitch correction.

10. Return to the embroidery screen and press Start

Watch at 01:56

When the position lines up with the break, tap the small exit icon at the lower right of the stitch panel. Check that the direction pad is back. With your hands clear, press the physical button with the blue ring below the display. Watch the machine resume from the selected point and check that stitches form across the missed section.

The finger points to the lower-right exit icon for the stitch controls.
The finger points to the lower-right exit icon for the stitch controls.
The direction pad is back and the operator presses the blue-ringed Start button.
The direction pad is back and the operator presses the blue-ringed Start button.
The machine is back at the hooped F for the restart.
The machine is back at the hooped F for the restart.

11. Zoom in and drag the preview

Watch at 02:08

To see the stitch path more clearly, tap the magnifying glass with a + at the lower right of the design preview. The percentage at the top right shows the display scale. In the video it changes from 100% to 120% on the first tap. Touch and drag inside the design area to bring the stitches you need into view.

The + magnifier is at the lower right of the design preview.
The + magnifier is at the lower right of the design preview.
The top-right percentage changes to 120% in this example.
The top-right percentage changes to 120% in this example.
Drag on the design itself to pan the enlarged preview.
Drag on the design itself to pan the enlarged preview.

12. Switch to zoom-out and see the whole design

Watch at 02:19

Continue tapping the + magnifier until the control changes to a − magnifier. Tap − to reduce the preview until the whole design fits on screen. The example returns to a 100% view of the letter F. This control changes the preview scale only.

The arrow marks the magnifier that changes to the − control.
The arrow marks the magnifier that changes to the − control.
The circled − magnifier reduces the preview scale.
The circled − magnifier reduces the preview scale.
At 100%, the complete letter F is visible again.
At 100%, the complete letter F is visible again.