SEWTECHSupport Center 简体中文

Fix Long Thread Tails After Trimming on the ST-1501 and SC-1501

Applies to ST-1501 / SC-1501 Demonstrated on ST-1501

Watch on YouTube ↗

Overview

This guide applies to the ST-1501 and SC-1501. The video shows the ST-1501. A long upper-thread tail left after trimming can be caught in the first stitches of the next color. Check the thread clamp, the upper tension knob and the controller’s trim length in that order. Stop embroidery before working at the needle head and have a 2 mm hex key ready.

Step-by-step guide

1. Identify the long upper-thread tail

Watch at 00:12

Pause after the trim and look between the needles and the hooped fabric. In the demonstration, a loose strand hangs down toward the blue F where the next color is meant to stitch. Follow the strand back to the needle area to identify the affected upper thread.

The finger points beside the loose strand hanging down toward the blue F.
The finger points beside the loose strand hanging down toward the blue F.

2. Locate the upper thread clamp

Watch at 00:24

At the front of the stopped machine, look just below the row of silver needle-area fingers for the long black clamp strip. The left-end inset shows the gap in this strip. A clamp that grips the upper thread too tightly is the first possible cause in the video.

The yellow arrow links the bottom clamp strip to the enlarged view of its left end.
The yellow arrow links the bottom clamp strip to the enlarged view of its left end.

3. Ease a tight clamp with a 2 mm hex key

Watch at 00:31

If the clamp is too tight, place the tip of the 2 mm hex key between its mating surfaces, as shown in the inset. Gently slide the key side to side in the gap and take it out before any test run. The video gives the tool size. Use a trim and color-change test to judge the result.

The presenter holds up the L-shaped 2 mm hex key used for the adjustment.
The presenter holds up the L-shaped 2 mm hex key used for the adjustment.
The straight end goes up into the clamp gap below the row of needles.
The straight end goes up into the clamp gap below the row of needles.
The inset shows the key tip between the black clamp surfaces as the hand slides it sideways.
The inset shows the key tip between the black clamp surfaces as the hand slides it sideways.

4. Tighten a loose upper thread

Watch at 00:44

Find the small spring-backed black knob for the affected thread in the top row, directly below the white thread tubes. The row of small dotted wheels sits beneath it. If the upper thread is loose, turn its top-row knob slightly clockwise as viewed from the front and test again. The video shows the direction of rotation.

The yellow arrow identifies the top row of tension knobs below the white thread tubes.
The yellow arrow identifies the top row of tension knobs below the white thread tubes.
The red arrows show clockwise rotation on the upper-row knob being turned.
The red arrows show clockwise rotation on the upper-row knob being turned.

5. Open More Set from the embroidery screen

Watch at 01:07

With embroidery stopped, tap the hand icon at the far right of the blue bottom bar. In the grid that appears, tap More Set, the middle tile of the second row. The controller opens a parameter list.

The fingertip is on the hand icon at the far right of the blue toolbar.
The fingertip is on the hand icon at the far right of the blue toolbar.
More Set is the center tile, with the text below the person-and-gear icon.
More Set is the center tile, with the text below the person-and-gear icon.

6. Open the Trim category

Watch at 01:12

From the first parameter list, tap the far-left button in the blue bottom bar, the one boxed in red in the video. On the category screen that opens, tap Trim in the left column just below Main Shaft. The trim parameters replace the category list.

The red box identifies the bottom-left button that opens the parameter categories.
The red box identifies the bottom-left button that opens the parameter categories.
The red box marks Trim, immediately below Main Shaft.
The red box marks Trim, immediately below Main Shaft.
Selecting Trim opens its own list of parameters.
Selecting Trim opens its own list of parameters.

7. Find Length of Trim on page 1/3

Watch at 01:19

On the demonstrated controller, Length of Trim is the bottom row on Trim page 1/3, immediately below Turn Off Trimming. Read the current value on the right. In the video it starts at 8.

The boxed Length of Trim row is below Turn Off Trimming. The page indicator reads 1/3.
The boxed Length of Trim row is below Turn Off Trimming. The page indicator reads 1/3.

8. Decrease the trim length and check the display

Watch at 01:24

If the current length is too high, tap the left arrow on the Length of Trim row and watch the number decrease. The video shows 8 changing to 5 as an example. Treat these as controller values and use your trim test to decide whether the new setting works for your job.

The inset shows 8 and both arrows. Use the left arrow directly beside the number.
The inset shows 8 and both arrows. Use the left arrow directly beside the number.
The controller now shows 5 on the same row.
The controller now shows 5 on the same row.

9. Exit the Trim parameters

Watch at 01:29

Check the new number on the Length of Trim row. The presenter then presses the exit icon at the right end of the light-blue row above the blue toolbar. The footage cuts to the hoop after this tap.

The Length of Trim row still displays 5 before exit.
The Length of Trim row still displays 5 before exit.
The fingertip points to the exit icon above the main blue toolbar.
The fingertip points to the exit icon above the main blue toolbar.

10. Verify a trim and the next color

Watch at 01:31

Remove the tool and keep your hands clear before restarting. Test a trim and the first stitches of the next color. Check that the remaining upper-thread tail stays clear of those stitches and the next color starts cleanly. Once both checks pass, continue the design. The video shows the machine back at the hooped F after the adjustment.

The final demonstration shows the needle lowered over the hooped F after the parameter adjustment.
The final demonstration shows the needle lowered over the hooped F after the parameter adjustment.