SEWTECHSupport Center 简体中文

Fix Thread Coming Out After Trimming

Applies to ST-1501 / SC-1501 Demonstrated on ST-1501

Watch on YouTube ↗

Overview

Use this guide for the ST-1501 and SC-1501 when the upper thread repeatedly slips out of the needle eye after automatic trimming. Stop stitching before inspecting the needles. Have a suitable replacement needle, needle-nose pliers and a screwdriver ready for the one-needle check. Keep a piece of hooped scrap fabric for the final trim-and-restart test.

Step-by-step guide

1. Inspect the cut thread tail

Watch at 00:23

After the machine stops, look at the upper thread tail against a light background. An occasional pullout can happen. If it repeats, compare the cut ends. A clean end makes a needle problem less likely. A ragged or frayed end is a reason to inspect that needle.

The dark thread on the left has a clean end. The red thread on the right has a rougher end.
The dark thread on the left has a clean end. The red thread on the right has a rougher end.

2. Check which needles are affected

Watch at 00:41

Note which needle lost its thread after trimming and compare it with other needles. If the symptom follows one needle, check that needle, its threading and its upper tension. If several needles repeatedly lose their thread after trimming, continue to the trim-length check.

The example alert at the lower left shows head 1 and needle 9. Use the needle number shown on your own machine.
The example alert at the lower left shows head 1 and needle 9. Use the needle number shown on your own machine.
The arrow singles out one needle in the row. Compare that position with neighboring needles.
The arrow singles out one needle in the row. Compare that position with neighboring needles.

3. Replace and orient the affected needle

Watch at 00:55

Switch the machine off before replacing the needle. Hold the affected needle with needle-nose pliers and loosen the clamp screw above it. Withdraw the old needle downward. Push the replacement fully up into the clamp with its long groove facing you and its scarf (the recess above the eye) facing the machine. Hold it in that position while tightening the screw.

The pliers hold the affected needle below the clamp at the start of the replacement.
The pliers hold the affected needle below the clamp at the start of the replacement.
The screwdriver reaches the clamp screw while the pliers support the needle below.
The screwdriver reaches the clamp screw while the pliers support the needle below.
The presenter points to the needle clamp where the new shank must seat fully.
The presenter points to the needle clamp where the new shank must seat fully.
The source diagram shows the long groove on the front and the scarf on the side facing the machine.
The source diagram shows the long groove on the front and the scarf on the side facing the machine.

4. Follow the entire threading path

Watch at 01:13

Follow the affected color from the upper tension assembly, past the thread wheels and lower guides, down through the take-up area to the needle eye. Check each guide in order for a missed guide or a thread that has slipped out, then rethread that position if needed.

Start tracing the affected thread at the upper row of knobs.
Start tracing the affected thread at the upper row of knobs.
Follow the thread past the wheels and larger lower knobs shown in the middle of the path.
Follow the thread past the wheels and larger lower knobs shown in the middle of the path.
The presenter points to the guide directly below the lower knobs.
The presenter points to the guide directly below the lower knobs.
Finish checking the path at the affected needle eye.
Finish checking the path at the affected needle eye.

5. Ease the affected needle’s upper tension if tight

Watch at 01:23

Use the small knob in the upper row for that needle. Excess tension can pull the upper thread back after a cut. If it is too tight, turn the knob slightly counterclockwise as shown, then check the next trim and restart.

The presenter identifies the small knobs in the upper row for the tension check.
The presenter identifies the small knobs in the upper row for the tension check.
The red arrows show the small knob turning counterclockwise to reduce tension.
The red arrows show the small knob turning counterclockwise to reduce tension.

6. Check trim length when several needles are affected

Watch at 01:40

If the symptom repeats across several needles, the automatic trim may be leaving the upper thread tail too short. The tail can slip out of the eye before the upper thread catches the bobbin thread on restart. With stitching stopped, note the current trim value before adjusting it.

The presenter points across the needle row while explaining the multi-needle symptom.
The presenter points across the needle row while explaining the multi-needle symptom.

7. Open More Set on the controller

Watch at 02:07

On the main embroidery screen, tap the hand icon at the far right of the bottom blue bar. In the 3 × 3 settings grid, tap More Set, the center tile in the second row. On the demonstrated controller it opens a password keypad.

The hand-shaped Settings icon is at the far right of the main screen’s blue bottom bar.
The hand-shaped Settings icon is at the far right of the main screen’s blue bottom bar.
More Set is the center tile in the second row of the settings grid.
More Set is the center tile in the second row of the settings grid.

8. Confirm the password prompt if shown

Watch at 02:11

If a password prompt appears, enter the code for your controller. The video shows 823456 on the demonstration machine. Tap the check mark on the keypad. When it is accepted, the controller opens the parameter list.

More Set may open a numeric keypad with a Password field.
More Set may open a numeric keypad with a Password field.
The check mark at the bottom of the keypad submits the entered code.
The check mark at the bottom of the keypad submits the entered code.

9. Open Trim and find Length of Trim

Watch at 02:21

On the parameter screen, tap the list icon at the far left of the pale footer, just above the blue toolbar. In the category list, tap Trim, immediately below Main Shaft. On Trim page 1/3, find Length of Trim (C18) at the bottom, just under Turn Off Trimming.

The inset and finger point to the category-list icon at the left end of the pale footer.
The inset and finger point to the category-list icon at the left end of the pale footer.
The Trim category is directly below Main Shaft.
The Trim category is directly below Main Shaft.
Page 1/3 shows Length of Trim at the bottom of the parameter list.
Page 1/3 shows Length of Trim at the bottom of the parameter list.

10. Increase the trim length one setting at a time

Watch at 02:28

Use the right arrow on the Length of Trim row to raise the value by one, then run a trim-and-restart test. If the same problem persists, add one more and test again. The screen in the video goes from 3 to 4 and then 5. Use your own starting value and check the displayed value after each press.

The demonstration starts at 3. The left and right arrows on the same row adjust this value.
The demonstration starts at 3. The left and right arrows on the same row adjust this value.
The display now reads 4 after the first increase.
The display now reads 4 after the first increase.
The next increase shows 5. These are the values on the demonstration machine.
The next increase shows 5. These are the values on the demonstration machine.

11. Return to the embroidery screen

Watch at 02:41

After each adjustment, use the exit icon at the right end of the pale Trim footer to return to the settings grid. Tap the grid’s lower-right exit icon to go back to the embroidery screen for the test. The design preview reappears.

The exit icon is at the far right of the pale footer below the trim value.
The exit icon is at the far right of the pale footer below the trim value.
On the settings grid, use the lower-right exit icon to return to embroidery.
On the settings grid, use the lower-right exit icon to return to embroidery.
The design preview reappears on the main embroidery screen.
The design preview reappears on the main embroidery screen.

12. Test a trim and the first stitches after it

Watch at 02:44

On scrap fabric in a hoop, stitch a short sample with a trim and restart on an affected needle. After the trim, verify that the upper thread is still through the eye and long enough for the next start. Confirm that it catches the bobbin thread and forms the first stitches without pulling out, then repeat on the other affected needles if applicable.

The final test is shown on hooped fabric below the needle head.
The final test is shown on hooped fabric below the needle head.
Watch the first stitches on your machine for successful thread pickup. The source shows the test from this wider angle.
Watch the first stitches on your machine for successful thread pickup. The source shows the test from this wider angle.