SEWTECHSupport Center 简体中文

Use the Touchscreen on the ST-1201 and SC-1501

Applies to ST-1201 / SC-1501 Demonstrated on ST-1201

Watch on YouTube ↗

Overview

Use the A15-pro controller to set up a T-shirt, a cap and flat embroidery. The ST-1201 demonstration shows the numbered setup pages in order. Have the design file, threaded needles and the frame or driver for your work ready. The example needle assignments and speeds belong to the jobs shown. Use the links beside the steps to see the exact controls and machine response.

Step-by-step guide

1. Power on and choose a language

Watch at 00:22

Turn on the machine and wait for the A15-pro home screen. If this is the first setup, open Settings with the gear at the bottom right. Tap the flags tile, then tap the circle beside your language. The demo selects English. Check the language selection and return to Settings.

The flags tile is in the middle row on the right.
The flags tile is in the middle row on the right.
Tap the selector to the right of English.
Tap the selector to the right of English.

2. Set and save the local time

Watch at 00:54

In Settings, tap the clock tile in the bottom row. Adjust the time with the controls above and below the numbers. Tap the check mark to save, then back out of Settings to the home screen.

Adjust the hour, minute and second fields on the time screen.
Adjust the hour, minute and second fields on the time screen.
Use the check mark at the bottom to save.
Use the check mark at the bottom to save.

3. T-shirt · Import a design from USB

Watch at 01:20

Have the design on a USB drive and the hooped garment ready. Insert the drive into the right side of the controller, then tap the USB icon on the right of the file screen. Select the design thumbnail and tap Import in the USB view. Edit the name in the dialog if needed and tap the check mark. Listen for the confirmation tone, then use Back and check that the design is listed in machine memory. The video uses USB for all three examples and also mentions Wi-Fi as a transfer option.

The USB drive is plugged into the side of the panel. Open it with the USB icon on the file screen.
The USB drive is plugged into the side of the panel. Open it with the USB icon on the file screen.
Select the thumbnail first, then tap the Import icon on the right.
Select the thumbnail first, then tap the Import icon on the right.
Confirm the import with the check mark below the file details.
Confirm the import with the check mark below the file details.
The cherry design is visible in the machine’s internal list.
The cherry design is visible in the machine’s internal list.

4. Delete or copy a stored design

Watch at 02:18

These are optional file-management actions. On the machine’s file list, select the design you intend to remove, tap Delete and confirm the prompt. Check that its thumbnail disappears. To export, leave the USB drive inserted, select a stored design, tap Copy and confirm with the check mark. Look for “Export Pattern Finished!” before returning to the list.

The delete prompt requires confirmation for the selected design.
The delete prompt requires confirmation for the selected design.
With a stored design selected, use the Copy control on the file page.
With a stored design selected, use the Copy control on the file page.
“Export Pattern Finished!” confirms the copy to USB.
“Export Pattern Finished!” confirms the copy to USB.

5. Page 2 · Set the design direction

Watch at 02:56

Select the design you will stitch in the machine’s list. Tap the second tab in the horizontal strip below the preview. Tap P in the Direction row to change the orientation. The cherry preview turns from horizontal to vertical in the demo. Tap P again if you need to return to the original direction, and check the preview against the way the garment is hooped.

P is in the first row of the Page 2 settings.
P is in the first row of the Page 2 settings.
The sideways cherry preview shows the direction change.
The sideways cherry preview shows the direction change.

6. Page 2 · Adjust angle and scale

Watch at 03:23

Tap Angle, enter the value on the number pad and confirm. The demo enters 20° to show the rotation, then puts it back to 0°. Use the X and Y scale fields to resize along each axis. The video illustrates increasing a scale value from 100 to 120. Check the resulting preview and size before continuing to Page 3.

Enter an angle with the on-screen keypad and confirm.
Enter an angle with the on-screen keypad and confirm.
The cherry preview is tilted after the 20° example.
The cherry preview is tilted after the 20° example.
The X and Y scale controls are below Angle.
The X and Y scale controls are below Angle.

7. Page 3 · Match the screen colors to the spools

Watch at 04:04

The numbered swatches represent the controller’s needle positions. Compare each swatch with the thread actually installed at that needle. In the demo, needle 8 is threaded green but displays purple. Tap swatch 8, choose green in the palette and tap the check mark. Check the updated swatch and preview before assigning the stitch order.

The palette opens after you select the needle swatch.
The palette opens after you select the needle swatch.
The swatch and affected part of the preview now appear green.
The swatch and affected part of the preview now appear green.

8. Page 3 · Assign the T-shirt color sequence

Watch at 04:55

Use the stitch-order rows on the left and the numbered needle swatches on the right. The cherry example uses needle 8 (green), 12 (red), 10 (black) and 1 (white), in that order. Choose needles to suit your own design and thread setup, then check both the sequence and the rendered colors.

The needle swatches on the right assign the active color step.
The needle swatches on the right assign the active color step.
The final cherry preview shows the intended colors after assignment.
The final cherry preview shows the intended colors after assignment.

9. Page 4 · Match the T-shirt hoop and position the design

Watch at 05:14

Open Page 4 and tap the hoop selector above the small control buttons on the left. In the grid, choose the entry that matches the hoop physically fitted to the machine and tap the check mark. Check the hoop outline in the preview. Use the arrow pad on the right to move the design. Rabbit gives faster travel and turtle gives finer movement. Use the center command and confirm its prompt if you want to return to the frame center.

The T-shirt example selects GH1010 100 × 100. Confirm the matching frame with the check mark.
The T-shirt example selects GH1010 100 × 100. Confirm the matching frame with the check mark.
The right-hand arrow pad moves the design within the displayed frame.
The right-hand arrow pad moves the design within the displayed frame.
The controller asks you to confirm before moving to frame center.
The controller asks you to confirm before moving to frame center.

10. Page 4 · Trace the T-shirt design

Watch at 06:05

Tap Trace in the left control group. Watch the red laser dot mark the design’s outer limits on the hooped shirt. Check every edge for clearance inside the actual hoop. If the path is too close to the frame, adjust the placement and trace again before stitching.

The Trace control is the rightmost button in the first row of the small controls.
The Trace control is the rightmost button in the first row of the small controls.
Check the traced boundary on the hooped shirt under the needle head.
Check the traced boundary on the hooped shirt under the needle head.

11. Page 5 · Choose color-change mode and speed

Watch at 06:23

Open Page 5. The needle icon marked A in the left-side control group indicates Automatic in the demo. The ST-1201 demonstration describes three color-change modes. Automatic continues through the sequence. Semi-automatic changes to the next needle and waits for you to press Start. Manual stops after each color and waits for you to select the next needle. Use the speed down/up controls in the lower left to set the speed for your work.

Page 5 is the operating page for color-change mode and stitch speed.
Page 5 is the operating page for color-change mode and stitch speed.
Adjust speed with the paired controls at the lower left.
Adjust speed with the paired controls at the lower left.

12. Confirm and start the T-shirt design

Watch at 07:10

After checking the file, color order, frame and trace, tap the embroidery confirmation control at the right end of the tab strip. Wait for the design to load and reappear in the preview. Press the physical Start button with the blue ring below the screen. Watch the first stitches to confirm the selected design starts in the traced area.

After confirmation, the screen shows the design loading.
After confirmation, the screen shows the design loading.
The cherry preview is loaded. The blue-ring Start button is below the screen, on the left.
The cherry preview is loaded. The blue-ring Start button is below the screen, on the left.
The needle head is over the hooped shirt as stitching begins.
The needle head is over the hooped shirt as stitching begins.

13. Cap · Prepare the driver and select cap mode

Watch at 07:34

With the machine off, make sure the cap driver is installed correctly. Power on and open the frame selector on Page 4. The demo selects CAP FRAME 270×70 in the second row on the right. Tap the check mark at the bottom. The controller warns that the carriage may move. Check the setup and clearance before confirming the prompt. When the narrow cap-frame outline appears, fit the hooped cap onto the driver.

CAP FRAME 270×70 is highlighted. Tap the check mark at the bottom.
CAP FRAME 270×70 is highlighted. Tap the check mark at the bottom.
The warning indicates that the frame may move after confirmation.
The warning indicates that the frame may move after confirmation.
The cap driver is installed below the needle head.
The cap driver is installed below the needle head.
Fit the hooped cap onto the driver after selecting cap mode.
Fit the hooped cap onto the driver after selecting cap mode.

14. Cap · Import the design and check direction

Watch at 08:05

Insert the USB drive, tap USB, select the cap design and use Import. After confirmation, return to the machine list and select the imported design. On Page 2, check the artwork direction before moving on to colors. The automatic cap-mode rotation is shown later, after embroidery confirmation.

The cap design is selected in the USB view before import.
The cap design is selected in the USB view before import.
The Page 2 preview shows the ST design upright during setup.
The Page 2 preview shows the ST design upright during setup.

15. Cap · Assign the two colors

Watch at 08:30

Open Page 3 and compare the numbered swatches with the threads on the needles. The ST lettering example assigns red to the first stitch color and blue to the second. Select the respective needle swatch for each color step. Check that S turns red and T turns blue in the preview.

The screen shows numbered needle swatches on the color page.
The screen shows numbered needle swatches on the color page.
The red S and blue T confirm the two assignments in this example.
The red S and blue T confirm the two assignments in this example.

16. Cap · Position the design in the cap frame

Watch at 09:00

Open Page 4 and check that the cap outline is displayed. Use the arrows to move the design, the turtle setting for fine moves and the rabbit setting for faster moves. If you choose to center the design, use the center function and accept its confirmation prompt.

The arrow pad sits to the right of the cap-frame controls.
The arrow pad sits to the right of the cap-frame controls.
Confirm the move if the screen asks to return the design to frame center.
Confirm the move if the screen asks to return the design to frame center.

17. Cap · Trace using the physical needle position

Watch at 09:21

Run Trace on Page 4 and watch the actual needle position relative to the cap and frame at the boundary. The red laser spot seen on the curved cap is unreliable for this check. Start only after the needle path is clear of the cap frame. Reposition and retrace if you need to change the placement.

The Page 4 preview shows the design inside the narrow cap boundary.
The Page 4 preview shows the design inside the narrow cap boundary.
Watch the actual needle over the cap. The visible red spot can be offset.
Watch the actual needle over the cap. The visible red spot can be offset.

18. Cap · Set speed, confirm rotation and start

Watch at 09:38

On Page 5, use the speed controls. The video recommends 600–700 stitches per minute for the cap example and sets 650. Confirm the embroidery and wait for the preview. The controller automatically turns the ST design 180° for the cap setup shown. Check the orientation, then press the blue-ring physical Start button and watch the first stitches.

The paired speed controls are on the lower left. Read the set speed between them.
The paired speed controls are on the lower left. Read the set speed between them.
The preview is rotated 180° and the presenter presses the blue-ring Start button.
The preview is rotated 180° and the presenter presses the blue-ring Start button.
After pressing Start, watch the needle position on the hooped cap.
After pressing Start, watch the needle position on the hooped cap.

19. Flat embroidery · Fit the hoop and load the design

Watch at 10:23

Make sure the flat hoop is installed with the material held flat. Insert the USB drive, open its file list, choose the design, tap Import and confirm. Return to the machine list and check that the imported design is available. Select it, open Page 2, and use P if the design needs reorienting. Check the flower preview against the material before going to Page 3.

The flat frame is already fitted with the white material under the head.
The flat frame is already fitted with the white material under the head.
Confirm the selected flower design in the USB import dialog.
Confirm the selected flower design in the USB import dialog.
Page 2 shows the flower preview above the direction controls.
Page 2 shows the flower preview above the direction controls.

20. Flat embroidery · Check the two needle assignments

Watch at 11:11

On Page 3, match the needle swatches to the actual thread colors. The flower example assigns needle 8 to the first color and needle 11 to the second. Check that the color-order display and the flower preview both update before opening the hoop page.

The swatches and current order are visible before reassignment.
The swatches and current order are visible before reassignment.
The flower preview updates after the needle selection.
The flower preview updates after the needle selection.

21. Flat embroidery · Select the frame and place the design

Watch at 11:55

On Page 4, open the frame selector. The video chooses the large rectangular frame because it matches the one already installed. Choose your matching frame and tap the check mark. Use the arrows to place the flower inside the green outline. Use turtle for fine moves or rabbit for faster travel, or run the center command to position it in the middle.

The flat-work example selects GH2036 360 × 200. Confirm the highlighted option at the bottom.
The flat-work example selects GH2036 360 × 200. Confirm the highlighted option at the bottom.
Page 4 shows the green frame outline, movement controls and design placement.
Page 4 shows the green frame outline, movement controls and design placement.

22. Flat embroidery · Verify clearance with Trace

Watch at 12:35

Tap Trace. Watch the red laser dot on the flat material as the machine follows the outside of the design area. Verify the entire path fits inside the actual frame, then check the design position against the green outline on the screen. If you adjust the position, trace again before moving to Page 5.

Watch the physical frame during the boundary check.
Watch the physical frame during the boundary check.
The presenter points to the design within the green frame boundary.
The presenter points to the design within the green frame boundary.

23. Flat embroidery · Set speed, confirm and start

Watch at 12:58

On Page 5, the demo uses Automatic color change and sets 800 stitches per minute as its flat-work example. Adjust the speed and tap the embroidery confirmation control at the right end of the tab strip. Wait for the flower design to reappear, then press the blue-ring Start button. Watch that the machine begins at the intended spot.

The speed controls are at the lower left of Page 5.
The speed controls are at the lower left of Page 5.
Confirm embroidery from the right end of the tab strip.
Confirm embroidery from the right end of the tab strip.
The flower preview is loaded and the presenter presses Start.
The flower preview is loaded and the presenter presses Start.
Check the first stitches on the flat work under the needle head.
Check the first stitches on the flat work under the needle head.