SEWTECHSupport Center 简体中文

Troubleshoot ST-1501 Frame Driver Collisions

Applies to ST-1501

Watch on YouTube ↗

Overview

Use this guide when selecting a hoop on the ST-1501 causes a loud knock or grinding from the X-axis beam. Stop the machine immediately if the sound occurs. Once the machine is stationary, check that the hoop and drive beam have a clear path before restarting for the settings check.

The video shows one ST-1501 configuration. Verify the required X/Y setting for your machine before changing it. If your controller or machine configuration differs, contact SEWTECH support for the correct value.

Step-by-step guide

1. Recognize the noise during hoop selection

Watch at 00:19

The video starts with a round hoop profile selected from the touchscreen. When the controller applies the selection, the carriage moves and the X-axis beam makes a loud, unusual noise. If you hear that sound during hoop selection, go straight to the emergency stop.

The operator selects the round hoop tile in the second row.
The operator selects the round hoop tile in the second row.
The inset shows the physical hoop and carriage as the movement begins.
The inset shows the physical hoop and carriage as the movement begins.

2. Press the emergency stop

Watch at 00:26

Press the red emergency stop on top of the touchscreen housing immediately. The frame motion stops and the display goes dark on the demonstrated machine. Wait for all movement to stop before checking the hoop’s path.

The green arrows point to the red emergency stop on top of the controller.
The green arrows point to the red emergency stop on top of the controller.
A dark touchscreen is the visible response immediately after the stop.
A dark touchscreen is the visible response immediately after the stop.

3. Release the emergency stop clockwise

Watch at 00:36

Once the machine has stopped and the travel path is clear, turn the red button clockwise to release it. In the video, the button rises and the display stays dark until the machine is switched on again.

The curved arrow shows the clockwise turn that releases the button.
The curved arrow shows the clockwise turn that releases the button.
The red button has risen. The display is still dark.
The red button has risen. The display is still dark.

4. Switch the machine back on

Watch at 00:44

Use the main rocker switch beside the power cord inlet. Wait for the SEWTECH boot screen to clear and the touchscreen controls to return before opening Settings.

The inset locates the black rocker switch next to the plugged-in power cord.
The inset locates the black rocker switch next to the plugged-in power cord.
The SEWTECH logo appears while the controller starts up.
The SEWTECH logo appears while the controller starts up.

5. Open Settings and More Set

Watch at 00:50

Tap the gear at the bottom right of the touchscreen. In the Settings grid, tap More Set in the center. On the controller shown in the official video, enter 823456 on the password keypad and tap the check mark. The advanced parameter table opens.

The gear at the far right of the bottom toolbar opens Settings.
The gear at the far right of the bottom toolbar opens Settings.
More Set is the center tile with a person-and-gear icon.
More Set is the center tile with a person-and-gear icon.
The video highlights the six digits and shows the check mark used to confirm.
The video highlights the six digits and shows the check mark used to confirm.

6. Open the parameter category list

Watch at 01:02

In the advanced parameter table, tap the small list icon at the far left of the light-blue navigation strip, just above the dark-blue toolbar. That opens the list of parameter categories.

The inset points to the list button at the lower left of the parameter table.
The inset points to the list button at the lower left of the parameter table.
The left column now lists categories, including Mac. Config.
The left column now lists categories, including Mac. Config.

7. Open Machine Configuration page 3

Watch at 01:07

Select Mac. Config. (Machine Configuration) in the category list. Use the right arrow beside the page counter at the bottom of the table to advance until it reads 3/4. On the demonstrated controller, this is where Y001 appears.

Mac. Config. is below Trim in the category list.
Mac. Config. is below Trim in the category list.
The operator taps the arrow to the right of the 2/4 counter.
The operator taps the arrow to the right of the 2/4 counter.
The bottom counter now reads 3/4.
The bottom counter now reads 3/4.

8. Record the original Y001 value

Watch at 01:14

Find Y001, labeled X/Y Limit Position. Write down or photograph the full value before changing it. The video shows X Left Y Front as the starting value. Check that you are on Y001. The row immediately below is Y002, X/Y Limit Origin.

The magnified Y001 row reads X Left Y Front before any change.
The magnified Y001 row reads X Left Y Front before any change.

9. Set the verified X/Y position

Watch at 01:35

Tap the arrow on the Y001 row to cycle through the paired X/Y choices. On the machine shown, the right arrow cycles past X Right Y Back. Stop when the field reads X Right Y Front, the confirmed value for this example. Leave the other machine parameters as they are.

The fingertip is on the right arrow in the Y001 row.
The fingertip is on the right arrow in the Y001 row.
X Right Y Back appears briefly while cycling through the choices.
X Right Y Back appears briefly while cycling through the choices.
The row now reads X Right Y Front, the final value for the machine shown.
The row now reads X Right Y Front, the final value for the machine shown.

10. Return to page 4 of the main screen

Watch at 01:43

Use the exit icon at the right end of the Machine Configuration footer, then the exit icon above the bottom toolbar on the general Settings screen. On the main screen, tap the fourth tab from the left in the middle row of tabs, as shown. The hoop field and directional pad come into view.

The first exit is at the right end of the parameter footer.
The first exit is at the right end of the parameter footer.
The second exit is at the lower right of Settings, above the dark toolbar.
The second exit is at the lower right of Settings, above the dark toolbar.
The fourth main-screen tab opens the page with the hoop controls.
The fourth main-screen tab opens the page with the hoop controls.

11. Select the installed hoop and confirm

Watch at 01:48

Tap the frame field to the left of the directional pad. Choose the profile that matches the installed hoop. The video shows a round profile whose tile turns yellow. Tap the check mark along the bottom of the hoop menu. If the movement warning appears, check that the path is clear, remove a cap frame if necessary as directed on screen, then tap the warning’s check mark. The hoop outline appears back on the main screen.

The frame field just to the left of the directional pad opens the hoop menu.
The frame field just to the left of the directional pad opens the hoop menu.
The round hoop tile is highlighted in yellow. The menu’s check mark is near the lower right.
The round hoop tile is highlighted in yellow. The menu’s check mark is near the lower right.
The controller warns that the frame may move and asks you to check the cap frame.
The controller warns that the frame may move and asks you to check the cap frame.
The selected round hoop appears on the main screen.
The selected round hoop appears on the main screen.

12. Check that the beam travels smoothly

Watch at 01:55

Keep hands clear and watch the carriage as it moves across the X-axis beam. In the video the movement is smooth and the unusual noise is gone. If the knock, grinding, or jerking returns, press the emergency stop again and contact SEWTECH support before changing further parameters.

The hoop starts on the left side of the machine head.
The hoop starts on the left side of the machine head.
The carriage has moved the hoop to the right of the head. Watch the clip to hear the difference.
The carriage has moved the hoop to the right of the head. Watch the clip to hear the difference.
The hoop moves back beneath the needle head at the end of the test.
The hoop moves back beneath the needle head at the end of the test.