SEWTECHSupport Center 简体中文

Fix Wobbling on 8-in-1 and 6-in-1 Magnetic Hoops

Hoops covered: 8-in-1 and 6-in-1 magnetic hoops

Watch on YouTube ↗

Overview

This guide covers the SEWTECH 8-in-1 and 6-in-1 magnetic hoops. If the fitted hoop bounces during stitching, check the vertical space above the needle plate. The video shows how flat washers between the metal mounting brackets and the white frame arms can reduce excessive clearance. Switch the machine off and unplug it before inspecting or adjusting the mounting hardware.

Step-by-step guide

1. Recognize the up-and-down bounce

Watch at 00:01

The opening shows the fabric and hoop rising and dropping near the needle plate as the machine stitches. If you see this motion, stop the machine before checking the fit by hand.

The front edge of the hoop and the fabric move vertically beneath the presser foot.
The front edge of the hoop and the fabric move vertically beneath the presser foot.

2. Check the gap with the hoop seated

Watch at 00:12

Seat both sides of the hoop in the machine’s mounting arms as usual. Look from the front at the space between the bottom of the hoop and the top of the needle plate. The red marks in the video show where the frame sits too high in the example.

Both sides of the hoop slide into the machine’s mounting arms.
Both sides of the hoop slide into the machine’s mounting arms.
The red marker points to the large gap above the needle plate before adjustment.
The red marker points to the large gap above the needle plate before adjustment.

3. Check where the frame rebounds

Watch at 00:22

With the machine stopped, the presenter presses and releases the front of the hoop to show its vertical travel. The narration explains that a descending presser foot can push the high fabric and hoop down. The hoop then rebounds, and repeated movement at speed makes the shaking more pronounced.

Light pressure on the front edge shows how far the hoop can move down toward the plate.
Light pressure on the front edge shows how far the hoop can move down toward the plate.
After release, the frame sits back above the needle plate.
After release, the frame sits back above the needle plate.

4. Remove the hoop and lay out the hardware

Watch at 00:43

Keep the machine unplugged. Take the hoop to a workbench, then remove the three screws and metal bracket from each frame arm. The demo lays out a Phillips screwdriver, six screws, two brackets and 12 washers. SEWTECH lists SUS304 stainless steel M3 × 10 mm Phillips pan-head screws and SUS304 M3 flat washers (10 mm outer diameter, 3 mm inner diameter, 0.8 mm thick).

The screwdriver is at the left, with the removed hardware laid out on both sides of the frame.
The screwdriver is at the left, with the removed hardware laid out on both sides of the frame.
The video labels 12 washers for the six mounting holes in this example.
The video labels 12 washers for the six mounting holes in this example.

5. Stack washers over the three holes on one arm

Watch at 00:58

Line up the flat washers over the three threaded holes used by the bracket on the white frame arm. The video stacks two at each of those holes. Center the washers so the screw can pass through them, and use only as much thickness as needed to correct the fit on your setup.

The arrow identifies one of the threaded holes on the white frame arm.
The arrow identifies one of the threaded holes on the white frame arm.
The next washer stack goes over a second hole along the same arm.
The next washer stack goes over a second hole along the same arm.
The three washer stacks sit flat over the bracket’s mounting holes.
The three washer stacks sit flat over the bracket’s mounting holes.

6. Fit and tighten the first metal bracket

Watch at 01:10

Pass the three screws through the metal bracket and set it back in its original orientation over the washers. Start all three screws, then tighten them evenly with the Phillips screwdriver without overtightening. If the added thickness leaves the M3 × 10 mm screws too short, choose longer M3 Phillips pan-head screws that engage securely and clear nearby parts and the frame’s travel path.

The three screws go through the metal bracket before it is lowered onto the washer stacks.
The three screws go through the metal bracket before it is lowered onto the washer stacks.
The washer stacks are sandwiched between the bracket and the white arm.
The washer stacks are sandwiched between the bracket and the white arm.
Hold the bracket steady while tightening the mounting screws.
Hold the bracket steady while tightening the mounting screws.

7. Match the washer height on the other arm

Watch at 01:24

Repeat the washer placement at the corresponding three holes on the opposite arm. The example uses the same two-washer stack at each point on both sides. Keep the added thickness even so the frame seats level.

The arrow shows the corresponding mounting hole on the second arm.
The arrow shows the corresponding mounting hole on the second arm.
All three washer stacks on the second arm are centered before the bracket goes on.
All three washer stacks on the second arm are centered before the bracket goes on.

8. Secure the second bracket and check both sides

Watch at 01:35

Set the second bracket over the washer stacks and start its three screws. Hold the bracket in place and tighten the screws evenly. Before putting the hoop back on the machine, check that neither bracket rocks, both sit level, and the washers stayed centered while tightening.

The second bracket is aligned over the three washer stacks.
The second bracket is aligned over the three washer stacks.
The screwdriver is on the last mounting screw on this side.
The screwdriver is on the last mounting screw on this side.
Both metal brackets are back on the outer sides of the frame arms.
Both metal brackets are back on the outer sides of the frame arms.

9. Slide the hoop back into the machine

Watch at 01:53

Support the hoop by both sides and slide the brackets into the machine’s mounting arms. Check from the front that both sides are seated and the frame is level before comparing the gap.

Both hands guide the brackets into the machine’s mounting arms.
Both hands guide the brackets into the machine’s mounting arms.
The hoop is seated on both sides for the clearance check.
The hoop is seated on both sides for the clearance check.

10. Compare the gap and check free travel

Watch at 01:57

Compare the gap at the same spot above the needle plate. The video ends with a visibly smaller gap and a hand check on the hoop. Once the brackets are secure and the frame is level, SEWTECH recommends a slow test run. Check that the frame travels without touching the machine and no longer bounces up and down before returning to normal speed.

Before adjustment, the bottom of the hoop sits well above the needle plate.
Before adjustment, the bottom of the hoop sits well above the needle plate.
After adjustment, the arrow marks a visibly smaller gap at the same spot.
After adjustment, the arrow marks a visibly smaller gap at the same spot.
The presenter presses lightly again to check the adjusted fit.
The presenter presses lightly again to check the adjusted fit.